^ V / WHITE ..y /// « TO CORD BLUE TO field 01-93 Part Qty. Part Qty. Fig- No. Used Description Fig- No. Used Description 1 911136-9 4 SCREW M4X20 35 221229-7 1 SPIRAL BEVEL GEAR 15 2 156050-4 1 GEAR HOUSING (WITH PLANE BEARING 6, 36 254002-0 1 WOODRUFF KEY 3 214006-4) 37 961006-2 1 RETAINING RING S-10 3 211088-7 1 BALL BEARING 6000DDW 38 221232-8 1 SPIRAL BEVEL GEAR 35 4 911216-1 SCREW M5X14 39 911121-2 3 SCREW M4X14 5 285604-1 1 BEARING RETAINER 35 40 285616-4 1 BEARING R

USBOOS-l Specific Safety Rules 1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2. Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. 3.Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal

Service or maintenance performed by unqualified personnel could result in a risk of injury. 24.,When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury. USBOOS-l Specific Safety Rules 1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2. Accessories must be rate

Depressed center wheel should not be used after it has been worn down to 75 mm (3") in diameter for Models 9560CV, 9563CV or 90 mm (3-1/2") for Models 9561 CV, 9564CV and 9565CV in diameter. Use of the wheel after this point is unsafe and it should be removed from service and rendered unusable by intentional destruction. The tools equipped with electronic function are easy to operate because of the following features. Electronic speed control for obtaining constant speed Possible to get fine fin

11. Avoid accidental starting. Ensure the switch is in the off-position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. 12. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. 13. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool

USD205-1 Symbols The followings show the symbols used for tool. . volts . amperes . hertz . alternating current . no load speed . Class II Construction . orbits per minute 3 FUNCTIONAL DESCRIPTION FUNCTIONAL DESCRIPTION CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Switch action 1. Switch CAUTION: • Before plugging in the tool, always check to see that the tool is switched off. To start the tool, press the " I " side of t

Specific Safety Rules 1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2.Accessories must be rated for at last the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. 3.Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of th

0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it Battery cartridge Set plate i from the barrel. 0 To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully before using the tool. 0 Do not use force when inserting the battery cartridge. If the cartridge does not slide in easi