/ Camarillo, CA 93011 Copyright © 1996 by Central Purchasing Incorporated. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Central Purchasing Incorporated. For technical questions and replacement parts, please call 1-800-444-3353. CHICAGO HEHIlHPowTToobl INDUSTRIAL SPECIFICATIONS Item # 31309 I AmpsA/olts I 5.5 Amps /120 VAC [ Power 660 Watts I No load speed 10000 RPM Weight 6-

Make sure power is off before plugging in the Sander/ Grinder. 2. Check Sander / Grinder for damaged parts. 3. Make sure all clamps, locks, and bolts are tight. 4. Remove any adjusting keys or wrenches. 5. Make sure guards are in place and in proper working order. Warning! Make sure table is securely locked into place following adjustments. Table should be secured to a flat, level surface capable of supporting weight of the Sander/Grinder as well as workpiece material being used. 6. Give Sander

Introduction Congratulations on the purchase of your new John Deere 1/4-Inch Right Angle Grinder! You can be assured your angle grinder was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance. John Deere 1/4-Inch Right Angle Grinder is designed for grinding and deburring operations in confined areas. This rear exhaust tool features a built-in regulator for convenient speed control and a lock-off lever

Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. 12. DON’T OVERREACH. Keep proper footing and balance at all times. 13. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 14. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like. 15. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position bef

To keep the double insulation system effective, follow these precautions: a. Only a AUTHORIZED JOHN DEERE DEALER should disassemble or assemble this power tool, and only genuine JOHN DEERE replacement parts should be installed. b. Clean the exterior of the power tool only with a soft cloth moistened with soapy water, and dry thoroughly. Never use solvents, gasoline or thinners on plastic components; otherwise the plastic may dissolve. 4 1/4-Inch Disc Grinder Operator's Manual IMPORTANT SAFETY IN

(See Figure C, and Assy. Diagram.) BRAKE PIN (#18) SIDE HANDLE (#20) WOOL COVER (#45) BRUSH CAP (#40) CARBON BRUSH (#41) BRUSH HOLDER (#42) VARIABLE SWITCH (#31) BACK HANDLE (#39) POWER CORD (#36) FIGURE C OPERATING INSTRUCTIONS NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 12 of this manual. SKU 46507 PAGE 8 To Attach The Rubber Backing Plate And Sandpaper: To Attach The Rubber Backing Plate And Sandpaper: . Caution: Prior to installing the Rub

All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions please call 1-800-444-3353 SPECIFICATIONS ITEM DESCRIPTION Max. Air Pressure 90 PSI Air Speed 20,000 RPM Fitting Size 1/4” NPT Collet Sizes 1/4” 1/8” Accessories 11 mm Collet Wrench (Qty: 1) 17 mm Collet Wrench (Qty: 1) SAVE THIS MANUAL You will need this manual for the safety warnings and precau

If you are using the tool outdoors, use an extension cord rated for outdoor use (signified by “WA” on the jacket). Maintenance. For your safety, maintenance should be performed regularly by a qualified technician. There are certain applications for which this tool was designed. This tool shall not be modified and/or used for any application other than which it was designed. All accessories must be rated for at least the RPM speed recommended on the tool’s warning label. Wheels and other accessor

If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. 2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury. 3. Wear suitable gloves to reduce the vibration effects on the user. 4. Use tools with the lowest vibration when there is a choice between different processes. 5. Include vibration-free periods each

BEFORE EACH USE, inspect the general condition of the tool. Check for loose hardware, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. 2. AFTER USE, wipe external surfaces of the tool with clean cloth. 3. Care of Grinding Wheels - As a result of normal use, grinding wheels may become cracked, grooved, rounded, chipped, out of true or loaded with foreign material. Cracked wheels should be repla