Mount wheel on a rod or pencil through arbor hole and tap the side of the grinding wheel (in the positions shown in Figure 4) with a light, non-metallic implement such as the handle of a screwdriver. A sound and undamaged wheel will give a clear tone. If cracked, there will be a dead or dull sound and not a clear ring. If damaged, the wheel should not be used. 7. As the grinding wheel diameter decreases with use, the position of the work rest should be adjusted. Optimally, the distance between t

2. Turn the air tool upside down. 3. Simultaneously (at the same time), pull the trigger and pour a teaspoon of Campbell Hausfeld oil in the air inlet. After an air tool has been lubricated, oil will discharge through the exhaust port during the first few seconds of operation. Thus, the ex-haust port must be covered with a towel before applying air pressure. Failure to cover the exhaust port can result in serious injury. 4. Release the trigger and connect the air tool to the air supply. Cover th

Stop using any tool if discomfort, numbness, tingling, or pain occur, and consult a physician. Operation LUbrICaTIOn Proper lubrication is the owner’s responsibility. Failure to lubricate the air tool properly will dramatically shorten the life of the tool and will void the warranty. REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping. © 2010 Campbell Hausfeld/Scott Fetzer For parts, product & service information IN241203AV 2/10

14. Do not put hands near or under moving parts. 15. Always secure workpiece in a vise or clamp. Do not misuse this product. Excessive exposure to vibration, work in awkward positions, and repetitive work motions can cause injury to hands and arms. Stop using any tool if discomfort, numbness, tingling, or pain occur, and consult a physician. Operation LUbrICaTIOn Proper lubrication is the owner’s responsibility. Failure to lubricate the air tool properly will dramatically shorten the life of the

SPeeD aDjUSTmenT This sander is equipped with a regulator for speed adjustment (See Replacement Parts List for Specifications). aTTaCHInG SanDInG PaD/DUaL aCTIOn SanDerS Adhesive backed discs are recommended. To apply the sandpaper, align outside edge and press self adhesive paper onto the pad. Change sandpaper as needed. Disconnect the air tool from the air supply before attaching the sanding pad. Do not operate the sander if sanding pad is not securely tightened. Always replace a worn or damag

Technical Service For information regarding the operation or repair of this product, please call 1-800-543-6400. Figure 6 - Model AT121002 Figure 7 - Model AT121102 Protruding Hub Attach Air Hose Material Hose Hose Connector Conduit Nut Wheel Cap Do not cover this hole when dry blasting Operating Instructions Type of abrasive (Sieve/Size) application Sand (20-40) General purpose use Removing light rust and paint from metal, wood or other . surfaces; wood finishing; metal cleaning; glass and ston

This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear. This manual contains information that is very important to know and under-stand. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize this information, observe the following symbols. Danger indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Warning indicates a potentially hazardou

No oil in tool 2. Lubricate the tool according to the lubrication instructions in this manual 3. Low air pressure 3a. Adjust the regulator on the tool to the maximum setting (If applicable) 3b. Adjust the compressor regulator to tool maximum while the tool is running free 4. Air hose leaks 4. Tighten and seal hose fittings if leaks are found 5. Pressure drops 5a. Be sure the hose is the proper size. Long hoses or tools using large volumes of air may require a hose with an I.D. of 1/2” or larger

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. BUILT TO LAST Detail Sander Description Detail sanders are designed for uniform sanding and polishing in corners and tight spaces. Ideal for flush sanding along e

Repuesto Bolsa para polvo DG027900AV 1 Garantia Limitada DURACION: A partir de la fecha de compra por el comprador original tal como se especifica a continuacion: Un ano 2. QUIEN OTORGA ESTA GARANTIA (EL GARANTE: Campbell Hausfeld / The Scott Fetzer Company 100 Production Drive, Harrison, Ohio 45030 Telefono: (800) 543-6400 3. QUIEN RECIBE ESTA GARANTIA (EL COMPRADOR): El comprador original (que no sea un revendedor) del producto Campbell Hausfeld. 4. PRODUCTOS CUBIERTOS POR ESTA GARANTIA: Cualq