If the impeller is not rotated manually prior to installation, the pump may fail to activate. If the impeller’s rotation is difficult or completely resistant, contact the Liberty Pumps Customer Service Department. Mechanical Installation 3-2 STORAGE BEFORE USE Liberty pumps are shipped from the factory ready for installation and use. They should be held in storage if the pump station is not complete. If storage is necessary, the pump should remain in its shipping container. It should be stored i

The HandiMet® 2 provides a self contained four-stage grinding station with controlled water flow for lubrication and cooling of the specimen plus the flushing away of debris. Unique water activated clamping holds abrasive papers firmly in position during grinding. Includes a selection of four abrasive paper rolls, water hoses and operating instructions. Accessories 30-5143-240-001 240 grit CarbiMet® Abrasive Paper Roll 30-5143-320-001 320 grit CarbiMet® Abrasive Paper Roll 30-5143-400-001 400 gr

Grasp the lifting chain and shake the pump to ensure a good seat with the gasket. The pump is suspended by the bracket ears. The weight of the pump compresses the gasket against the mating flange of the guide bracket base. 4. The lifting chain may be removed from the hoist and hooked near the upper guide rail bracket. IMPORTANT: For 3-phase pumps, check for proper rotation before installing pump into basin. See figure A for proper rotation. 4. AFTER THE PUMP IS INSTALLED, THE ELECTRICAL CHECKS O

Damaged O-Ring between oil chamber and motor plate C. Damaged cable ACTION A. Check power supply Check out electrical system for loose connections Check operating voltage B. Check circuit protectors C. Check external cable for damage – repair D. Inspect and remove jamming object E. Refer to Symptom 5 and 6 A. Check rating and replace with proper size B. Check current draw C. Verify connections. See wiring diagram D. Inspect external cable, replace if worn or damaged E. Remove obstruction F. Chec

Install covers, close doors making certain that no wires are pinched and that all enclosure parts are properly aligned and tightened. ENERGIZING THE CONTROL PANEL OR BREAKER FOR THE FIRST TIME IS POTENTIALLY DANGEROUS. LICENSED ELECTRICAL PERSONNEL SHOULD BE PRESENT WHEN THE PANEL OR BREAKER IS ENERGIZED FOR THE FIRST TIME. IF FAULTS CAUSED BY DAMAGE OR POOR INSTALLATION PRACTICES HAVE NOT BEEN DETECTED, SERIOUS DAMAGE CAN RESULT WHEN POWER IS APPLIED (REFER TO SECTION 5). 4-4 FLOAT SWITCHES 1.

Contents • General Information • Introduction • Mechanical Installation • Electrical Connection • Operation • Warranty Installation Manual 5647000F Omnivore Sewage and Grinder Pumps IMPORTANT: Prior to installation, record Model, Serial Number, and Code Number from pump nameplate for future reference. MODEL _____________________ SERIAL _____________________ CODE _____________________ INSTALLATION DATE _____________________ 7000 Apple Tree Avenue Bergen, NY 14416 Phone: (800) 543-2550 Fax: (585)

• The installation must be in accordance with the National Electric Code, Uniform Plumbing Code, International Plumbing Code, as well as all applicable local codes and ordinances. • Sump and sewage pumps often handle materials which could cause illness or disease. Wear adequate protective clothing when working on a used pump or piping. • Never enter a pump basin after it has been used. Sewage and effluent can emit several gases which are poisonous. • Keep clear of suction and discharge openings.

Liberty Pumps, Inc. shall not be liable for any loss, damage or expenses resulting from installation or use of its products, or for consequential damages, including costs of removal, reinstallation or transportation. There is no other express warranty. All implied warranties, including those of merchantability and fitness for a particular purpose, are limited to two years from the date of purchase. This Warranty contains the exclusive remedy of the purchaser, and, where permitted, liability for

Operation of these models will be according to the control selected. Make sure the electrical specifications of the control selected properly match the electrical specifications of the pump. Always refer to control panel instructions for proper installation. Introduction 2. 2-1 INTRODUCTION This manual was prepared to assist you in the correct installation, operation, and maintenance of your Liberty pump. Please read it completely before installing the pump. Make certain that you are familiar wi