4 thru 13) 4 99110518 Scroll Housing for Blower - Counterclockwise 5 99020150 Blower Wheel - Counterclockwise 6 99150490 Sheet Metal Screw 10-16 x 3/4 PH Truss Head 7 98008836 Frame Half - Counterclockwise 8 99100497 Rubber Isolation Mount 9 99080156 Motor 10 99020149 Blower Wheel - Clockwise 11 99110519 Scroll Housing for Blower - Clockwise 12 98005573 Cross Brace 13 98005572 Frame Half - Clockwise 14 97007953 Bottom Cover - White 97007957 Bottom Cover - Alm

May be purchased locally. ** Not Illustrated. *** For use in Ventless configurations only. 7

• Observe the surroundings and ensure that no people or animals can come into contact with the blower. • Place the machine on the ground, press the machine body against the ground with your left hand (NOTE! Not with your foot). Then grasp the starter handle with your right hand and pull the cord. Fuel safety • Always use a fuel container with an anti-spill valve. • Never refuel the machine while the engine is running. Always stop the engine and let it cool for a few minutes before refuelling. •

Always stop the engine and let it cool for a few minutes before refueling. When refueling, open the fuel cap slowly so that any excess pressure is released gently. Tighten the fuel cap carefully after refueling. Always move the machine away from the refueling area before starting. English- ---11 STARTING AND STOPPING Min.10ft. (3m) SCleantheareaaroundthefuelcap. Contaminationinthetankcancauseoperatingproblems. SEnsurethatthefueliswellmixedbyshak- ingthecontainerbeforefillingthetank. Starting and

• Always start by filling half the quantity of petrol required. Then add the entire oil quantity. Mix (shake) the fuel mixture. Fill the remaining quantity of petrol. • Mix (shake) the fuel mixture carefully before filling in the machine‘s fuel tank. • Do not mix more than max. one month’s supply of fuel. • If the machine is not used for a long period of time, the fuel tank should be emptied and cleaned. ! ! WARNING! The catalytic converter muffler gets very hot during and after use. This also a

The throttle lock (4) must be pressed down before the trigger will actuate the throttle. Fan casing (7) The blower fan casing (7) together with the impeller (13) provide high performance air discharge. Inspection cover (11) An inspection cover is located on the underside of the fan casing. Removal of this cover allows access for cleaning and inspecting the impeller. The inspection cover can only be opened by means of tools. If the vacuum tube is used, it must be fitted to the opening in the insp

Hearing protection. 2. Eye protection. 3. Face mask in dusty environments. When operating the blower, the blower must be secured to the shoulder strap. The strap should be worn over the shoulder as shown in the adjacent figure. 15 14 16 – English USING THE BLOWER ! ! WARNING! Never point the blower nozzle at people or animals. The high-velocity air stream can contain particles that may cause serious injury, especially if the blower has previously been used for vacuuming. Be careful, particurlarl

114 00 25-95 CONTENTS Introduction ......................................... 3 Key to symbols....................................4 Safety instructions .............................. 5 Description .......................................... 7 Fuel handling ..................................... 12 Start and stop .................................... 14 Using the blower ............................... 16 Maintenance ...................................... 20 Technical data.............................

FUEL HANDLING Fuel CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained.When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture. ! WARNING! Always ensure there is adequate ventilation when handling fuel. Mixing • Always mix the gasoline and oil in a

Husqvarna Forest & Garden must warrant the emissions control system on your small off- road engine for the period listed below provided there has been no abuse, neglect or improper maintenance of your equipment.Your emissions control system may include parts such as the carburetor, ignition system, catalytic converter, fuel tank, filters and other associated components. Also, included may be hoses, belts, connectors, sensors, and other emission-related assemblies. Where a warrantable condition e