Log: 
Veiller à une bonne aération pendant toute manipulation de carburant._ Petrol • Use good quality unleaded or leaded petrol. • The lowest octane recommended is 90. If you run the engine on a lower octane grade than 90, so-called knocking can occur. This gives rise to a high engine temperature, which can result in serious engine damage. ° For work with continuously high revs a higher octane rating is recommended. Benzin * Bleifreies oder verbleites Qualitätsbenzin verwenden. « Als niedrigst
If cracked, be sure to replace without delay. WARNING To reduce the risk of injury associated with contacting rotating parts, stop the engine before installing or removing attachments. Never take off the Guard Net . Always disconnect the spark plug before performing maintenance or accessing movable parts. USING THE PRODUCT WARNING While using the product, if abnormal noise or vibration occurs, stop the engine immediately and contact the nearest Husqvarna servicing dealer for assistance. Check
Place the waist belt around your waist and not too far down on the stomach. Tighten the waist belt strap so that you feel the weight of the blower resting on your hip. • Be sure to always tighten the buckle in front of your body. F8 F9 F10 WARNING• If you are not using a waist belt, be sure to remove it from the unit and store it. • There is a risk that the belt will be caught, toppling the unit. • There is a danger that the belt will be sucked into the fan. F11 F12 English 17 .. FUEL WARNING •
d) Do not refuel a running engine. e) Avoid spilling fuel or oil. Always wipe unit dry before using. f ) Move at least 10 ft. (3 meters) away from the fueling point before starting the engine. g) Always store gasoline in a container approved for flammable liquids. h) Make sure the unit is properly assembled and in good operating condition. i ) Do not use the blower near a fire, as aiming the blower in the direction of a flame may cause flammable substances to ignite. Safety Precautions English 8
6. In the event that any part must be replaced or any maintenance or repair work not described in this manual must be performed, please contact the nearest Husqvarna servicing dealer for assistance. 7. Do not use any accessory or attachment other than those bearing the Husqvarna mark and recommended for the unit. 8. Under no circumstances should you ever take apart the product or alter it in any way. Doing so might result in the product becoming damaged during operation or the product becoming u
3. OIL FOR 4-CYCLE ENGINE USE - It can cause spark plug fouling, exhaust port blocking, or piston ring sticking. 4. Mixed fuels which have been left unused for a period of one month or more may clog the carburetor and result in the engine failing to operate properly. 5. When storing the product for a long period of time, clean the fuel tank after rendering it empty. Next, activate the engine and empty the carburetor of the composite fuel. 6. When scrapping the used mixed oil container, scrap it
• Specifications are subject to change without notice. English 14 .. SWIVEL JOINT 1. Connect the blower and swivel joint with flexible hose. Clamp both ends of the flexible hose securely with the hardware supplied with the unit. NOTE A light lubricant may be used to ease assembly of flexible hose to blower elbow. .. THROTTLE LEVER [330BT/350BT/370BTS/380BTS] 1. Set up the throttle holder to the swivel and tighten the screw on the holder. When setting up the holder, please make sure to match the
Flexible Hose 20. Pipes 21. Pad 22. Flat Nozzle (Option) 23. “EMISSION” Label .. DISPOSAL When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations. Frame: PE (Polyethylene) Harness: Chemical fiber Throttle lever: Metal, Plastic Volute case, Volute cover, Engine cover: PA66GF (Glass-reinforced nylon), Brass Pad: Chemical fiber Flexible hose: EVA (Ethylene vinyl acetate) Pipes: PP (Polypropylene) Fan: PA66GF (Glass-reinforced nylon) Element: Paper, Urethane
of May 3, 1989 “relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements. of May 8, 2000 “relating to the noise emissions in the environment” 2000/14/EC. For information relating to noise emissions, see the chapter Technical data. The following standards have been applied: ISO 22868:2005, CISPR 12:2005, ISO 14740:1998. TUV Rheinland Japan Ltd., 9F 3-19-5 Shin Yokohama, Kohoku-ku, Yokohama 222-0033, Japan, has performed voluntary type examination on behalf of Husqvarna AB
. . . . . . . . . . . . . . . . . . . . 7 WORKING PLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 FUEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 BEFORE STARTING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 USING THE PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
