As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture. 5. Indicate the contents on outside of container for easy identification. To avoid mixing up with raw gasoline or other containers. ■ FUELING THE UNIT 1. Untwist and remove the fuel cap. 2. Put fuel into the fuel tank to 80% o

Spark arrestor If your unit comes with spark arrestor screen and yet your local regulation requires use of spark arrestor for prevention against a possible fire, please attach it to the muffler by removing muffler protector and other related parts. (The spark arrestor meets the regulation of SAE J335-SEP90 and CSA CAN3-Z62. 1 -M77) 10 custsvc@tanaka-ism.com Owner.s ManualTHB-2500/THB-2510/TBL-4600/4610,TBL-505 THB-2500/THB-2510/TBL-4600/4610,TBL-505 Maintenance schedule Below you will find some

s Man s Mans Mans Mans Mans Man ual ualualualualual Model Numbers: THB-2500,THB-2510, THB-2500,THB-2510,THB-2500,THB-2510,THB-2500,THB-2510,THB-2500,THB-2510,THB-2500,THB-2510, TBL-4600,TBL-4610,TBL-505 TBL-4600,TBL-4610,TBL-505TBL-4600,TBL-4610,TBL-505TBL-4600,TBL-4610,TBL-505TBL-4600,TBL-4610,TBL-505TBL-4600,TBL-4610,TBL-505 BL BLBLBLBLBL O OOOOO WERS WERSWERSWERSWERSWERS P/N 12626 Date 08-10-01 TBL-4600 THB-2510 Supplier ToThe Outdoor Power Equipment Industry ISM, Inc. . 1028 4th Street SW .

When the engine is test run at the factory, the carburetor is basically adjusted. A further adjustment may be required, according to climate and altitude. The carburetor has one adjustment possibility: T = Idle speed adjustment screw. Idle speed adjustment (T) To adjust, turn IDLE Adjustment Screw (T) in (clockwise) to increase engine speed, out (counterclockwise) to decrease engine speed. Standard Idle rpm is 2500-3000rpm. CAUTION! The above adjusting procedure must be followed when adjustment

*Always move the unit at least 3 m (10 ft.) from the fueling area before starting. Before fueling, clean the tank cap area carefully, to ensure that no dirt falls into the tank. Make sure that the fuel is well mixed by shaking the container, before fueling. 5 custsvc@tanaka-ism.com Owner.s ManualTHB-2500/THB-2510/TBL-4600/4610,TBL-505 THB-2500/THB-2510/TBL-4600/4610,TBL-505 Starting CAUTION! Do not start if the pipe is obstructed by the ground or any other object. 1 .Set ignition switch (1) to O

• Empty the fuel tank before storing the tool. It is recommended that the fuel be emptied after each use. If fuel is left in the tank, store so fuel will not leak. • Store tool out of the reach of children. • Clean the unit carefully and store it in a dry place. • Make sure engine switch is off when transporting or storing. If situations occur which are not covered in this manual, take care and have good judgment. Contact your dealer if you need assistance. Pay special attention to statements pr

ITEM PART NUMBER DESCRIPTION QTY COMMENTS 6-16 0303190020 CUSION,RUBBER,BOTTOM 2 6-26 0193131980 BAND 2 6-27 8123190020 SCREW,G,M6x16 2 6-28 83531900200 NUT,F.M6 2 6-29 0163190020 STAY,BAND 1 6-30 0293131320 NUT,SPECIAL 4 6-31 0213190020 PAD,CUSHION 1 6-32 0463190020 FASTENER 4 6-34 5913190080 TANK,FUEL 1 6-35 5953190090 CAP,TANK 1 6-36 2233190090 PIPE,FUEL ASSY 1 6-37 8153190020 SCREW,J,M5x14 2 6-38 8303190020 WASHER,A 2 6-40 0203190080 FRAME 1 6-41 03031307200 BUFFER 2 6-42 0603190020 COLLAR 2

Self-measuring Bottle (24*) 7001101 Gallon Jug Commercial Size (6*) 4 Case Quantity ACCESSORIES 034-31302-801 Shoulder Strap MANUALS & CATALOGS 12626 Owner's Manual 12144 Parts Catalog SPECIAL TOOLS 006-29326-000 Flywheel Remover 001-29000-000 Tachometer 009-29326-000 Piston Pin Remover 070-2000W-500 Pressure Tester 070-2000W-501 Carb. Tool Kit FIG.l ENGINE FIGURE 1 THB-300 PARTS LISTING REF. PART NO. PART DESCRIPTION Q C S SERIAL NO REMARKS 1 002-01251-200 CYLINDER 1 C -J04588