Assessments - , GPA: ( )

Instruções de Operação Buhler, Modelo SNOW KING OH195SP

Fabricante : Buhler
Arquivo Tamanho: 1.84 mb
Arquivo Nome :

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

15. If engine does not start after following steps 1 thru 12, contact your Authorized Tecumseh Servicing Dealer. DO NOT attempt to start or troubleshoot this engine in any other way. 181-1275-14 4-Cycle • Snow King Engine Page 11 Page 12 4-Cycle • Snow King Engine 181-1275-14 Figure 24. Choke Control Positions STOP STOP STOP STOP STOP STOP STOP STOP STOP STOP STOP STOP STOP STOP STOP LH195SA/LH195SP OH195SA/OH195SP OH318SA/OH358SA LH318SA/LH358SA 1. “NO CHOKE” Position 2. “1/2 CHOKE” Position 3. “FULL CHOKE” Position 1 2 3 3 1 2 3 1 2 1 2 3 B. Engines with Recoil Starters If you have an electric starter see "A. Engines with Electric Starters" instructions on page 10. !WARNING DO NOT pull starter rope with engine running. Doing so may VOID YOUR WARRANTY. 1. To avoid carbon monoxide poisoning, be sure engine is outdoors in a well-ventilated area. 2. Be sure fuel valve, if present (see equipment manufacturer’s instructions) is open and all switches are on. See Figure 25. 3. Move engine speed control to “FAST” position. See Figures 26 and 27. 4. Set choke control to “FULL CHOKE” position (see equipment manufacturer’s instructions). See Figure 24 on page 12. Afterward, continue reading instructions below. 5. Hold the primer bulb in for one full second each time you press it. See Figure 28. • Make sure you cover vent hole with your thumb. • Repeat twice for a total of three primes. NOTES DO NOT use primer bulb to restart a warm engine after a short shutdown. Doing so will flood the engine and may result in equipment malfunction. If restarting a warm engine after a short shutdown, move engine speed control to “FAST” position and move choke control to “NO CHOKE” position. See Figures 24, 26 and 27 starting on page 12. Afterward, continue reading instructions below. 6. Operate equipment control to release engine brake or clutch, if present (see equipment manufacturer’s instructions). Fuel Tank Turn Valve Clockwise To “OFF” Position Position Shown Fuel Valve “OPEN” Figure 25. Fuel Valve Positions STOP STOP SLOW RUN FAST CHOKE PRIMER Figure 26. Typical Engine Symbols STOP1 5 1. Engine Speed Control 2. “STOP” Position 3. “SLOW” Position 4. “RUN” Range 5. “FAST” Position 4 3 2 Figure 27. Engine Speed Control Positions 1 2 1. Primer Bulb 2. Vent Hole Figure 28. Pressing Primer Bulb 181-1275-14 4-Cycle • Snow King Engine Page 13 !WARNING !WARNING When pulling starter rope, the rope can unexpectedly jerk back toward engine causing serious injury. To avoid this risk, carefully follow these instructions: 7. Grasp starter cord handle. See Figure 29. a. Pull rope out slowly until you feel drag. b. Without allowing the rope to retract, continue pulling rope with one rapid full arm stroke. c. Return rope slowly to original position. NOTES Following the instructions listed in the steps above avoids potential damage to the recoil mechanism. If recoil starter cord handle is frozen and will not operate engine, proceed as follows: a. Pull as much rope out of starter as possible. b. Release starter cord handle and let it snap back against starter to break up ice; these two steps should ONLY be done WHEN starter is FROZEN. c. If engine fails to start after 3 attempts repeat steps 1 thru 7 and try again. 8. When engine starts: a. Momentarily move choke control to “1/2 CHOKE” position until engine runs smoothly. See Figure 24 on page 12. Afterward, continue reading instructions below. b. Next, move choke control to “NO CHOKE” position. c. Finally, move engine speed control to desired speed in “RUN” range. See Figures 26 and 27 on page 13. Afterward, continue reading instructions below. NOTES If engine starts but falters when choke control is moved to “NO CHOKE” position: a. Momentarily move choke control back to “FULL CHOKE” position. b. Next, move choke control to “1/2 CHOKE” position until engine runs smoothly. c. Finally, move choke control to “NO CHOKE” position. If engine dies after choke control is moved to “NO CHOKE” position repeat steps 3 thru 10 to restart engine. 9. If engine fires but does not continue to run, move choke control to “NO CHOKE” position and start engine. See Figure 24 on page 12. Afterward, continue reading instructions below. 10. If engine fails to start after 3 attempts in the “NO CHOKE” position, move choke control to “FULL CHOKE” position and start engine. 11. If engine does not start after following steps 1 thru 10, contact your Authorized Tecumseh Servicing Dealer. DO NOT attempt to start or troubleshoot this engine in any other way. Figure 29. Recoil Starte...