Assessments - 2, GPA: 3 ( )

Fabricante : Ariens Arquivo Tamanho: 1.75 mb Arquivo Nome : Língua de Ensino:

DO NOT transport machine while engine is running. MAINTENANCE Ariens Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency. Should engine service be required, contact an Ariens dealer or an authorized engine manufacturer's service center. WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. SERVICE POSITION WARNING: Before tipping unit up onto housing, remove fuel so no spills will occur and remove battery (if equipped). Ensure unit is secure and will not tip over during maintenance. Place unit on a flat level surface. Tip unit forward onto front of impeller housing for service. Assure unit is secure and will not tip over. Strap and clamp onto bench if needed. GB - 19 MAINTENANCE SCHEDULE MAINTENANCE SCHEDULE MAINTENANCE SCHEDULE Service Performed Each Use Every 5 hrs. Every 25 hrs. Yearly Check Dual Handle Interlock • Check Fasteners • Check Clutches • Clean Engine • Check Engine Oil • Change Engine Oil * • Check Tire Pressure • Check Auger Gearcase • • General Lubrication • • Battery Maintenance • • * After first two hours of operation. CHECK DUAL HANDLE INTERLOCK Without the engine running, press down (engage) both clutch levers. Release attachment clutch lever. Attachment clutch should remain engaged until traction clutch lever is released, then both clutches must disengage. CHECK FASTENERS Make sure all hardware is tightened properly. CHECK CLUTCHES Auger / impeller must stop within 5 seconds when attachment clutch/impeller brake lever is released. Wheels must stop quickly when traction drive clutch lever is released. If clutches do not engage or disengage properly, adjust or repair before operation (see Service and Adjustments). CLEAN ENGINE Refer to Engine Manual for detailed instructions. CHECK ENGINE OIL The engine crankcase oil should be checked every 5 hours of operation. Oil level MUST be maintained in safe operating range on dipstick at all times or engine damage will result (See Engine Manual). Park unit on a level surface. Refer to Engine Manual for detailed instructions. CHANGE ENGINE OIL Change oil after first 2 hours of operation, thereafter change oil every 25 hours (more often if required). Refer to Engine Manual for detailed instructions. Run engine just prior to changing oil. Warm oil will flow more freely and carry away more contamination. CHECK TIRE PRESSURE Keep tires at pressure listed on the tire sidewall. CHECK AUGER GEARCASE IMPORTANT: Proper oil level must be maintained. Gear cases are filled to the correct level at the factory. Unless there is evidence of leakage, no additional lubricant should be required. Check oil level each season or every 25 hours of operation. To ensure adequate lubricant level: 1. Remove filler plug (Figure 10). Lubricant must be at least up to bottom of lubricant filler hole with unit resting on a level-surface. 2. Add lubricant if required. Allow oil to drain to level of plug and replace plug. IMPORTANT: Use only Ariens special gear lubricant L-2 (Part Number 00008000). GB - 20 GB - 21 GENERAL LUBRICATION IMPORTANT: Wipe each fitting clean before and after lubrication. IMPORTANT: DO NOT allow grease or oil to get on friction disc, friction plate or belts. NOTE: Apply Stens Mix Hi-Temp Grease or equivalent to the lubrication fittings. See Service Parts. Sno-Thro should be lubricated (Figure 11) at beginning of season or every 25 operating hours. Auger Shaft NOTE: To grease auger shaft, remove shear bolt nuts, and shear bolts. Turn auger on shaft while applying grease at zerk fittings. Replace shear bolt per instructions in Service and Adjustments. Figure 10 1. Auger Gearcase - Cast Iron 2. Oil Fill and Drain Plug 3. Auger Gearcase - Aluminum 1 2 2 3 1. Auger and Shaft 2. Discharge Chute 3. Sprocket/Pinion Assembly 4. Axle Shaft 5. Shift Lever Arm 6. Pinion Chain 7. Hex Shaft 8. Shift Link 1 1 6 8 3 5 4 Figure 11 2 1 1 7 Grease Oil OS0641 OS0741 CLEAN BATTERY (924332, 505, 506, 508) CLEAN BATTERY (924332, 505, 506, 508) WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. IMPORTANT: Battery is maintenance free. Do not tamper with or attempt to open battery. See Service and Adjustments for charging procedures. Terminals Keep battery and its terminals clean. IMPORTANT: Remove battery from unit before cleaning. Remove corrosion from battery terminals and cable connections with a wire brush, then wash with a weak baking soda solution. After cleaning, apply a thin coat of grease or petroleum jelly to terminals and cable ends to retard corrosion. SERVICE AND ADJUSTMENTS WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. DISCHARGE CHUTE DEFLECTOR (924118, 551) Deflector must stay in selected position while throwing snow. To adjust, loosen then retighten hardware to desired deflector drag force (Figure 12). Figure 12 Adjusting Hardware OS0113 Discharge Chute Deflector DEFLECTOR REMOTE (924121, ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :