60684 U.S.A. Part No. 14200-04 Printed in U.S.A. 6/88 ONE YEAR LIMITED WARRANTY ON CRAFTSMAN SNOW THROWER For one year from the date of purchase, when this Craftsman Snow Thrower is maintained, lubricated and tuned-up according to the instructions in the owner’s manual. Sears will repair, Iree of charge, any defect in material and workmanship. H this Craftsman Snow Thrower is used for commercial purposes, this warranty applies for only 90 daysfrom the date of purchase. This warranty does n

DUAL STAGE SNOW THROWER Optional Electric Starter Available •Assembly •Operation •Maintenance •Repair Parts Sold by Sears, Roebuck and Co., Chicago, IL 60684 Pari No. 770-66750 (RB60B02) CRAFTSMAN WARRANTY LIMITED TWO YEAR WARRANTY ON CRAFTSMAN SNOW THROWER For two years from the date of purchase, when this Craftsman Snow Thrower ¡s maintained, lubricated and tuned up according to the instructions in the owner’s manual. Sears will repair, free of charge, any defect in material and workma

60179 U.S.A. PRINTED IN U.S.A. RULES FOR SAFE OPERATIONS Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS, IT MEANS --ATTENTION! BECOME ALERTJ YOUR SAFETY IS INVOLVED, Exercise caution at all times, when using power equipment. 1. Read the tractor and snow blade owners manuals and know how to operate your tractor before using tractor with snow blade attachment

ELECTRIC START SNOW THROWER WHEN ORDERING REPAIR PARTS, ALWAYS Each SNOW THROWER has its own MODEL NUMBER found on the engine mount frame. Each ENGINE has its own MODEL NUMBER found on the BLOWER HOUSING. Always mention these MODEL NUMBERS when requesting service or Repair Parts for your SNOW THROWER. All parts may be orderedthrough Sears, Roebuck and Company Service Centers and most Retail Stores, GIVE THE FOLLOWING INFORMATION: * PRODUCT -"SNOW THROWER" * MODEL NUMBER -536.886331 * ENGINE MODE

This manual provides information regarding the setup, operation, and maintenance of this product. We have made every effort to ensure the accuracy of the information in this manual. The manufacturer reserves the right to change this product at any time without prior notice. Please keep this manual available to all users during the entire life of the snow thrower. Copyright 2005 Yardworks(R). Do not reprint without written authorization. TABLE OF CONTENTS GENERAL SAFETY PROCEDURES ...............

HAZARD TO OPERATOR, BYSTANDERS, PROPERTYOR UNIT MAY Look for this symbol, It means --ATTENTION! BECOME ALERT! A EXIST, Page Page OWNERS INFORMATION ........................... 2 impeller/Auger Control Cable Adjustment ......... 10 MAINTENANCE AGREEMENT ....... :. .............. 2 Carburetor Adjustment .......................... 10 "WARRANTY ....................................... 2 Spark Plug Adjustment .......................... 10 OPERATIONAL PRECAUTIONS ...................... 3 MAINTENANCE ..

= 11 11 11 ,=H ,,,,HH= ,H 111 11,11,1 =,==,=H= 11 1111 SAFETY RULES _ CAUTION. ALWAYS DISCONNECT SPARK PLUG WIRE ANDPLACE WIRE WHERE IT CANNOT CONTACT SPARK PLUG TQ PREVENT ACCIDENTAL STARTING WHEN SETTING-UP, _li TRANSPORTING, ADJUSTING OR MAKING REPAIRS, IMPORTANT SAFETY STANDARDS REQUIRE OPERATOR PRESENCE CONTROLS TO MINIMIZE THE RISK OF INJURY. YOUR SNOW THROWER IS EQUIPPED WITH SUCH CONTROLS. DO NOT ATTEMPT TO DEFEAT THE FUNCTION OF THE OPERATOR PRESENCE CONTROL UNDER ANY CIRCUMSTANCES. TRA

A 9/16" or adjustable wrench is required. B. Slide the slotted end of the handles under the cupped washers. C. Secure the upper hole in the handles with 3/8" cupped washers and 2" long hex bolts. Cupped side of washers go against the handles. Do not tighten at this time. 5 I INSTALLING THE CHUTE CRANK ASSEMBLY 1. Attach the chute crank assembly to the handle and handle panel as follows. A. Thread one 5/16" hex nut about halfway onto the eyebolt on the chute crank assembly. B. Insert the

® Cut allfourcomersof the cartonfromtop to bottom and lay laythe panelsflat,. e Removethe packingmaterialfrom the shifterplate and upperhandleassembly. e Rollthesnowlhmweroffthecartonby pullingonthe lower handle,, NOTE: Thedrive systemmay betightwhenyoufirstuse yoursnowthrower.It loosensup as youuse ito e To completeupper handle installationand install chutecrankassembly,see To InstallThe UpperHandle and CrankAssemblyparagraphon page8. NOTE: Ifthecableshave becomedisconnectedfromthe clutchlevers

• Remove the belt cover (See Fig 26) • Engage the auger drive clutch lever, • Measure the distance between the belt guides and the belt (See Fig 28)° The distance should be 3/32" for each guide. • If adjustment is necessary, loosen the belt guide mounting bolts. Move the belt guides to the correct position Tighten the mounting bolts o Reinstall the belt cover. o Reconnect the spark plug wire REM -_BI_.__I |_.BOLT LOOSEN BOLT,.._ LOOSEN BOLT PANEL TRACK CONNECTING ROD ,,,, H i m, Jll,J ..... TO A