Assessments - 3, GPA: 3.7 ( )

Fabricante : JVC Arquivo Tamanho: 3.74 mb Arquivo Nome : Língua de Ensino:

2. For an optional secondary antenna source, connect an antenna (or cable) to ANT-2 AUX. 3. If you have subscribed to a CableCARD™ service, the CableCARD can now be inserted into the CableCARD SLOT. Using a phillips screwdriver, remove the CableCARD cover screws. Insert the CableCARD, then replace the cover and screws. If you need more information regarding this service, please contact your cable service provider. CableBoxbackpanelsectionINDIGITALSERVICEPORTIEEE1394INPUT/OUTPUTAUDIOANT-2AUXANT-1MAINCableCARDSLOT–(DTV/CABLE/VHF/UHF)– IncomingCableOUT INOUTOUTTWOWAYSPLITTER1.2.2.3.3.4.4. TVbackpanel(sectiondetail) DIGITALSERVICEPORTIEEE1394INPUT/OUTPUTAUDIOANT-2AUXANT-1MAINCableCARDTMSLOT–(DTV/CABLE/VHF/UHF)– 1.2. TVbackpanel(sectiondetail) OptionalSecondaryAntennaorCablePrimaryWallOutletCable3.CableCARDTMSLOT(coverremoved) Figure 2. Connecting a Cable Box Figure 1. Wall Outlet Cable Note: NetCommand® will assume that your Cable Box is connected as shown above. Also, that Channel 3 is the default output channel for the cable box. If either the connections or output channel are different, use the Change option of Edit NetCommand to apply the changes. IMPORTANT Additional connection cables are not provided with the TV. They are available at most electronic stores. Connecting a Single Analog Antenna or Separate UHF and VHF Antennas Single Antenna (not for use with CableCARD™) Figure 3 A 300-Ohm to 75-Ohm transformer is required. This is not included with the TV. For antennas with twin flat lead 1. For antenna with twin flat leads, connect the 300-Ohm twin leads to the 300-Ohm to 75-Ohm transformer. 2. Push the 75-Ohm side of the transformer onto ANT-1 MAIN on the TV back panel. For antennas with coaxial lead 3. Connect the coaxial lead directly to ANT-1 MAIN on the TV back panel. Separate UHF and VHF Antennas Figure 4 A UHF/VHF combiner is required. This is not included with the TV. 1. Connect the UHF and VHF antenna leads to the UHF/VHF combiner. 2. Push the combiner onto ANT-1 MAIN on the TV back panel. ExternalAntennaorCableBackSideFlatTwinLeadUHFAntenna(Channels14-69) VHFAntenna(Channels2-13) 300Ohmto75OhmCombinerFlatTwinLeadUHFVHFTVbackpanel(sectiondetail) SERVICEPORTIEEE1394INPUT/OUTPUTDIGITALAUDIOCableCARDSLOTANT-2AUXANT-1MAIN–(DTV/CABLE/VHF/UHF)– 1.2. SERVICEPORTIEEE1394INPUT/OUTPUTDIGITALAUDIOCableCARDTMSLOTANT-2AUXANT-1MAIN–(DTV/CABLE/VHF/UHF)– 300-OhmFlatTwinLeadOptional300-Ohmto75-OhmMatchingTransformer75-OhmCoaxialCableTVbackpanel(sectiondetail) 3.2.1. Figure 4. Connecting separate UHF and VHF Antennas Figure 3. Connecting an Antenna Mitsubishi strongly recommends against using antennas with twin flat leads. Twin flat lead antenna wires are subject to interference which may adversely affect the performance of the TV. We recommend using coaxial antenna cable. Connecting VCR Video and Audio to an Antenna or Wall Outlet Cable VCR to Antenna or Wall Outlet Cable Figure 5 A two-way RF splitter, 3 coaxial cables, right and left audio cables and S-Video or Video cables are required. These are not included with the TV. 1. Connect the incoming cable or Antenna to IN on the RF splitter. 2. Connect one coaxial cable from OUT on the RF splitter to ANTENNA IN on the VCR back panel. 3. Connect one coaxial cable from OUT on the RF splitter to ANT-1 MAIN on the TV back panel. 4. To use the TV speakers with the VCR, connect a set of audio cables from AUDIO OUT on the VCR back panel to INPUT 1 AUDIO-LEFT (MONO) and AUDIO-RIGHT on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel. If your VCR is mono (non-stereo), connect only the white (left) cable. 5. Connect either an S-Video or Video cable from VIDEO OUT on the VCR back panel to INPUT 1 VIDEO on the TV back panel. Only one type of video cable should be connected. S-Video is recommended, if available. 6. For NetCommand® controlled recordings, connect a Video cable from VIDEO IN on the VCR back panel to MONITOR OUTPUT AUDIO/VIDEO 1 on the TV back panel. 7. Complete the NetCommand controlled recording connection by connecting a set of audio cables from AUDIO IN on the VCR back panel to MONITOR OUTPUT AUDIO/VIDEO 1 AUDIO-LEFT (MONO) and AUDIO-RIGHT on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel. TUBER DIGITALSERVICEPORTIEEE1394INPUT/OUTPUTAUDIOANT-2AUXANT-1MAINCableCARDTMSLOT–(DTV/CABLE/VHF/UHF)– S-VIDEOVIDEOAUDIO- LEFT/ (MONO) AUDIO- RIGHTINPUTMONITOROUTPUTAUDIO212COMPONENTYPbPr(480i/480p/1080i) 21YPbPrAUDIO- LEFT/ (MONO) AUDIO- RIGHTDVIDigitalVideoDigitalAudioAnalogAudioS-VideorecommendedifavailableAttachonlyonecabletype TVbackpanel4. –(DTV/CABLE/VHF/UHF)– 5. S-VIDEOVIDEOAUDIO- LEFT/ (MONO) AUDIO- RIGHTINPUT12 ANT-1MAINMONITOROUTPUTAUDIO/VIDEO1 7. 3.6.7. HS-U748VCRbackpanelIfyourVCRhasavideochannelorRFON/OFFswitch,setittoOFF. 5.4. 5.6. 2. S-VideorecommendedifavailableWhiteRedWhiteRedWhiteRedWhiteRedAttachonlyonecabletype I...

Baixe o seu

Para fazer o download, introduza 2 dígitos :