Assessments - 3, GPA: 5 ( )

Fabricante : Hitachi Arquivo Tamanho: 3.74 mb Arquivo Nome : Língua de Ensino:

A security card (CableCARD) provided by your cable operator is required to view encrypted digital programming. Certain advanced and interactive digital cable services such as video-on-demand, a cable operator’s enhanced program guide and data-enhanced television services may require the use of a set-top box. For more information call your local cable operator. Please see page 15 for instructions on how to insert the CableCARD. PleasecallXYZCableatxxx-xxx-xxxxtoactivatecableservice. Theywillneedthesenumbers: HostIDX-XXX-XXX-XXX-XXXCableCARDTMID:X-XXX-XXX-XXX-XXXSeeowner'smanualforfurtherinformation IMPORTANT To use a CableCARD, the primary incoming cable must be connected to ANT-1 MAIN. Connecting: Helpful Hints Q My VCR (or other device) does not have two sets of stereo audio outputs. How can I connect this device’s audio to both the TV and the A/V Receiver? A. There are two solutions: 1. Connect the single set of stereo audio outputs to the TV only. Use Edit NetCommand® to change the setup of this device. In the Connection screen of “Change” make sure both audio and video for the TV input are checkmarked and neither the audio or the video for the AVR input are check marked. This will allow the NetCommand system to use the TV outputs to transfer the device’s audio to the A/V Receiver. See Edit NetCommand in the next chapter for details. 2. Use RCA type “Y” splitter cables to split the device’s audio output to be connected to both the TV and the A/V Receiver. Q. I have both the TV monitor stereo audio output and TV digital audio output connected to the same input designation on my A/V Receiver. How do I switch between analog audio and digital audio? A. This depends on the individual A/V Receiver. Some A/V Receivers will switch automatically to digital when a digital audio signal is supplied. Other A/V Receivers can be manually switched by remote control. For these types of A/V Receivers, see Edit NetCommand in the next chapter for NetCommand control of these features. Some A/V Receivers will require that you make this change on the front panel of the A/V Receiver. Q. The front panel of my A/V Receiver is too tall or too convex for the IR emitter signal to reach the remote control sensor of the A/V Receiver. What can I do? A. There are several possible solutions. 1. Mount the IR Emitter on the top, front edge of the A/V Receiver over the remote control sensor. Use tape to secure it in place. 2. Mount the IR Emitter on the underside of the shelf above the A/V Receiver (if the A/V Receiver is in a cabinet). Use double sided tape to secure it in place. 3. Some small stick-on emitters from other manufacturers may be compatible with this TV’s IR Emitter jacks. These may be used instead of the supplied IR Emitters. Q. I occasionally need to see the menu from my A/V Receiver. How can I connect it to the TV for this purpose? A. You can connect the video output of the A/V Receiver to an unused input on the TV. Then use Edit NetCommand to “Add” this as an “Other” device, not an A/V Receiver. On the “Connection” screen, indicate which TV input was used and checkmark the video box. Make sure the TV input audio box and both the audio and video boxes for the AVR input are not checkmarked. You should also name this device so you can easily identify it on the Device Selection Menu. You can also use Input 3 (Camcorder) on the front panel. Q. I have a high definition receiver I would like to connect and it also has an S-video output I would like to be able use as well. Is there any way to connect this receiver both ways? A. Yes, this item will appear twice in the Device Selection Menu. Just add this unit once using the Antenna and once using one of the S-video inputs. Make sure you indicate that this is the same manufacturer for both. We suggest that you connect stereo audio outputs with the S-video to the TV so that you do not need to use two inputs on the A/V Receiver. If this is a NetCommand compatible HDTV receiver and HD or SD outputs can be switched by remote control, see Edit NetCommand in the next chapter for NetCommand control of this feature. 3 NetCommand® Setup and Editing NetCommand® Pre-Memorized Devices28 Remote Control Functions: Overview29 Remote Control Functions: Operation, Care, Sleep Timer30 NetCommand® OnScreen Buttons31 3D Graphical Menu System32 NetCommand® Initial Setup33 Edit NetCommand® Adding an A/V Receiver35 Adding Devices38 Changing, Deleting Devices, Finish Screen42 Device Selection Menu43 Using the Device Menu Button to Display Menus44 NetCommand® Pre-Memorized Devices Below is a list of several manufacturers devices tested and shown to be compatible with NetCommand. These devices can be controlled without changing the setting of the remote control from TV to another product. NetCommand may be able to operate additional models since many manufacturers use the same control signals to operate some or all of the models they offer. This chart lists only the models that have been tested with NetComma...

Baixe o seu

Para fazer o download, introduza 2 dígitos :