Assessments - 4, GPA: 4.8 ( )

Fabricante : JVC Arquivo Tamanho: 6.35 mb Arquivo Nome : Língua de Ensino:

Power and Power Off). When the original remote control uses a single button for both functions, learn only the first of the paired functions. ** This function is performed only when the Input Selection Menu is displayed and the device icon is highlighted. *** Channel Up/Down as Guide Page Up/Down in effect only after pressing GUIDE; returns to channel functions after pressing ENTER or CANCEL. † If there are two ENTER keys, learn the ENTER key used for channel selection here. The ENTER button on the remote sends the correct IR code when digits are entered. ‡ Learn the sub-channel separator if a special key is used to add a separator (dash or dot) in a digital channel. Press the CANCEL button on the remote to add the separator ‡‡ DVD includes functions for DVD, DVD2, DVR, and HD disc. ‡‡‡ The GUIDE key is unavailable for a cable box guide when TV Guide On Screen is enabled. Chapter 3. TV Setup Initial NetCommand® Setup What You Need to Know About NetCommand • NetCommand setup is optional. • NetCommand operates by sending signals from the TV to your other devices via the IR emitters, telling the devices to play, record, change inputs, adjust volume, change channels and many more functions. All this is accomplished with the TV’s remote control and the slide switch left in the TV position. • The IR “Learning” feature of NetCommand allows the TV to learn the remote control signals for your A/V devices. • NetCommand® can control IEEE 1394 devices by sending control signals over a FireWire® cable. • You can choose the level of NetCommand control for your home theater. Limited Setup. Perform a limited setup if you: Want NetCommand to control only a few devices, such as the TV, a playback device (like a DVD player), and a cable box. With this setup, you can use the TV’s remote control to operate these devices. Want to use TV Guide On Screen® to control your cable box and VCR and/or A/V disc. After performing this setup, you can use the TV’s remote control to operate these devices. Want the ease and flexibility of NetCommandcontrolled recording, with seamless setup of time-delayed or immediate recordings among networked devices. Full Setup. Perform a full setup if you want to give NetCommand the following additonal control: Control a surround sound A/V receiver. Automatically change input selections for the A/V receiver. Initial NetCommand Setup for Most Device Types • To set up an A/V receiver, see “Additional Setup Using the NetCommand Menu” later in this chapter. • For setup later, or to make changes to the setup, see “Additional Setup Using the NetCommand Menu” later in this chapter. 1. Connect and position the IR emitters as described in chapter 2, “TV Connections.” 2. Have the remote controls for the TV and the other device ready before beginning. Set the TV remote control’s slide switch to the TV position. 3. In the Auto Input sensing screen (see figure 8), highlight the Learn button and press ENTER to open the Learn screen for the device (see figure 9). NetCommand “Learn” button Name you select for the device Figure 8. Highlight the Auto Input Sensing screen’s Learn button and press ENTER to open the NetCommand Learn screen. Figure 9. In the NetCommand Learn screen, you tell the TV to remember key commands to send to another device via an IR emitter. 4. The first function highlighted in the Learn screen is always Power (On). Aim the TV’s remote control at the TV and press ENTER to begin learning for that function. 5. When the Power (On) text starts flashing, aim the device’s remote control at the TV and press and hold the POWER key until a check mark appears in the box. If the text stops flashing before the check mark appears, repeat this step. 6. If the device has a separate POWER OFF key, press to highlight the check box for Power Off. Repeat the preceding step to “learn” the POWER OFF key. If device has no POWER OFF key, skip this step. By completing “learning” for the power keys, the TV’s remote control now operates the power function for the device when you set it as the current viewing device in the Input Selection menu. Point the remote control at the TV to control the device. Chapter 3. TV Setup Initial NetCommand® Setup, continued 7. Press the keys on the TV’s remote control to highlight other keys on the list. Repeat steps 4 and 5 for each additional function you wish to control through NetCommand. 8. If the device’s remote control has keys that do not appear in the list, you can associate up to four keys with the F1 through F4 keys. For example, for a DVD player, assign the F1 and F2 keys to the DVD player’s CHAPTER SKIP FORWARD and CHAPTER SKIP BACK keys. Perform NetCommand setup for the F keys the same as you did for the named keys. 9. Press EXIT to continue with setup for additional devices. Additional Setup Using the NetCommand Menu Use the NetCommand menu at any time to: • See a list of all connections to the TV. • Set up TV Guide On Screen® or make changes to the setup. • Add NetCommand contro...

Baixe o seu

Para fazer o download, introduza 2 dígitos :