Assessments - 5, GPA: 3.8 ( )

Fabricante : Mitsubishi Electronics Arquivo Tamanho: 6.35 mb Arquivo Nome : Língua de Ensino:

The green LED will flash quickly for about one minute. When the green LED stops flashing, you may turn on the TV. The changes you made most recently, before using SYSTEM RESET, may be lost. Changes you made previously, however, are not lost. TV Reset Menu 1. Select any device from the Input Selection menu. 2. Press MENU followed by 123 to open the Reset Service Menu. CAUTION: All settings except V-Chip will be reset to the original factory defaults Read on-screen warnings before proceeding, as some user data or settings may be erased. 3. Press ENTER to reset TV defaults. Demo Mode This TV has a demo mode for use in retail stores. To turn off demo mode: 1. Press MENU. 2. When the Main menu appears with Setup highlighted, press ENTER. 3. When the Setup menu opens, press to highlight the on-screen Demo Mode Off button. 4. Press ENTER. Service and Support Service If you are unable to correct a problem with your TV, consult your Mitsubishi dealer or a Mitsubishi Consumer Relations at (800) 332-2119. • DO NOT adjust any controls other than those described in this Owner’s Guide. • DO NOT remove the protective back cover of your TV. Support • To order replacement or additional remote controls, lamp cartridges, or Owner’s Guides, visit our website at or call (800) 553-7278. • For questions: Call Consumer Relations at 800-332-2119. E-mail: MDEAservice@mdea.com Website: Important All lamps replaced under warranty must be returned to Mitsubishi where they will be inspected for defect verification. 1 1111 112 22 A AAp ppp ppe een nnd ddi iic cce ees ss Appendix E: Troubleshooting, continued General TV Operation 1. 2. 3. 4. 5. 6. 7. 8. 9. Symptom A fan is running even while the TV is powered off. The TV remote control does not work. TV does not respond to the remote control or to front panel control and TV will not power on or off. When a device is selected from the Input Selection menu, the screen is blue (no signal source). Devices are grayed out in the Input Selection menu or the Split Screen Input Selection menu. You have forgotten your Parental Lock pass code. Rating restrictions are not working. On-screen displays appear each time you change a function. Cable provider needs information to start CableCARD™ service. Normal TV operation. When the TV is off, internal components continue to draw power and must be cooled by the fan. Remarks • Check that the batteries are installed correctly. • Check that the slide switch is set to TV. • Be no more than 20 feet from the TV when using the remote control. • Program the remote control to operate the TV or other device. Use the System Reset button. • Make sure the selected device is turned on. • Begin play of the VCR. • A recording is in progress. Cancel the recording to select the device. • PCs and 1080p sources cannot display in the Split Screen sub-picture. See Appendix A, Bypassing the Parental Lock. Open the Parental Lock menu and: • Verify that the U.S. Ratings or Other Ratings setting is On. • Check the Lock Time/Unlock Time to check if rating restrictions are disabled. • Rating restrictions apply only to content on ANT 1 and ANT 2, INPUT 1–3, and IEEE 1394 inputs. Normal TV operation. On the remote control, press MENU and then enter the numbers 999 to display the Host ID and CableCARD™ ID information. TV Channels Symptom 1. The TV takes several seconds to respond to channel changes. Remarks • It is normal for digital channels to take longer to tune in. • Press ENTER after a channel number to avoid delays. • Use a 4-digit number for an over-the-air digital channel. • Use a 6-digit number for digital cable channels if your cable service is able to recognize 6-digit channel numbers. 2. You cannot access a channel. 3. Name options are not available for some channels. • Use number keys instead of CH / . • Be sure the channel you want to view is in memory. See “Channel Menu” in chapter 5, “TV Menu Settings.” • Check that the TV is turned to the correct device or antenna for that channel by pressing the INPUT button. • Make sure the Parental Lock is off. • If you cannot tune to a virtual digital channel even though the TV has already memorized digital channels, tune to the actual channel number used by the broadcaster. The virtual channel will then be automatically added to memory. Only memorized analog channels can be named. 4. When ChannelView™ list is displayed, infor- Available information is sent from the broadcaster or cable pro mation appears incomplete vider. No other data is available. A AAAp ppp ppe een nnd ddi iic cce ees ss 1 111 113 33 Appendix E: Troubleshooting, continued TV Power On/Off Symptom 1. TV takes an excessively long time to power on. Remarks • When switched on, the TV needs time to boot up, just as a computer does. Also, the TV’s lamp requires a few moments to heat up to full brightness. • TV Energy Mode is set to Low Power. To change TV Energy Mode to Fast Power On: Press MENU, open the Setup menu, highlight...

Baixe o seu

Para fazer o download, introduza 2 dígitos :