Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. 8 Installation What You Need This thermostat includes two #8 slotted screws and two wall anchors for mounting. To install your thermostat, you should have the following tools and materials. ¦ Slotted Screwdriver(s) ¦ Electric drill and 3/16" bit ¦ Phillips Screwdriver ¦ Two 1.5 V (AA) size alkaline batteries ¦ Hammer Remove Old Thermostat CAUTION: Do not remove any wiring from existing thermostat before reading the instructions carefully. WIRES MUST BE LABELED PRIOR TO REMOVAL. ¦ IMPORTANT! Turn off the power to the furnace at the main power panel or at the furnace. ¦ Remove existing thermostat cover. See Figure 1. Some thermostats will have screws or other locking devices that must first be removed. Once wall mounting plate is exposed, look for wires. If wires are not visible, they may be connected to the back of the wallplate. Again, look for screws, tabs, etc. Some models have doors that open to expose wires and mounting screws. (See Figure 1). TYPICAL HOME THERMOSTATS Figure 1 Wall Mounting Plate Thermostat Cover Wall Mounting Plate Thermostat Cover Wire Labeling ¦ Each wire coming from the wall to the existing thermostat is connected to a terminal point on that thermostat. Each of these terminal points is usually marked with a code letter as shown in Table A on page 11. ¦ IMPORTANT! BEFORE DISCONNECTING ANY WIRES, APPLY THE SELF-ADHESIVE LABELS PROVIDED TO THE WIRE AS SHOWN IN TABLE A ON PAGE 11. (For example, attach the label marked W to the wire that goes to the W or H terminal on your existing thermostat.) IGNORE THE COLOR OF THE WIRES since these do not always comply with the standard. IMPORTANT! If wires marked Y & C are both present, C may be a Common wire and should not be used. If you have a wire marked C, do not connect it to any terminal. This wire is used only for non-battery powered thermostats. ¦ After labeling wires, disconnect them from the existing thermostat terminals. ¦ Remove existing wallplate. To make sure wires do not fall back into wall opening, you may want to tape them to the wall. ¦ If hole in wall is larger than necessary for wires, seal this hole so that no hot or cold air can enter the back of the thermostat from the wall. This air could cause a false thermostat reading. (continued) Mount Wallplate and Thermostat ¦ Remove the wallplate from your thermostat by pressing the release tab on the bottom of the thermostat. (See Figure 2.) ¦ Position wallplate on wall and pull existing wires through large opening. Then level for appearance. Mark holes for plastic anchors provided if your existing holes do not line up with those on the Hunter wallplate. ¦ Drill holes with 3/16" bit and gently tap anchors into the opening. Insert mounting screws provided into wall anchor and tighten. (See Figure 3.) holes until flush with wall. ¦ Reposition wallplate to wall, pulling wires through large opening. Insert provided mounting screws into wall anchors and tighten. GW/BY1Y/ORCRC1RHY1 Figure 2 Figure 3 Connect Wires and Mount Thermostat to Wallplate ¦ Straighten bare end of each wire and cut or strip it to 1/4” maximum. Insert each labeled wire into its matching terminal. NOTE: If a wire marked “C” is present, DO NOT connect it to the thermosat. ¦ Hold the wires in each terminal and tighten the terminal screws securely, otherw...
Este manual também é adequado para os modelos :Os termostatos - 44660 (3.29 mb)
Os termostatos - 44660 (3.29 mb)
Os termostatos - 44668 (3.29 mb)
Os termostatos - 44008-01 (3.29 mb)