Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
¦ Push excess wire back into hole to prevent interference with mounting of the thermostat. ¦ Make sure the Thermostats System Switch is set to OFF. ¦ Insert two AA size alkaline batteries, observing the polarity marked on the unit. your existing thermostat is marked... label the wire with this sticker: G / FGGW / H / BW/BW/BY / C* / M / OY/0Y/0RC / VCRCRCRH / R / VR / 4RHRH24 Volt24 Volt coolair conditioning compressorheatingfanY1Y1Y1heat pump compressor If you have not already programmed your thermostat, refer to page 13 to start setting up your programs. Page 34 will show you how to bypass the thermostats programming and activate temporary or permanent holds. See page 37 for other available options the thermostat has to offer. ¦ On the back of the thermostat, find Switch SW1 at the lower right-hand corner. 1) If your system is a gas furnace, then position the switch to HG. 2) If your system is an electric furnace, then position the switch to HE. 3) If your system is a single stage heat pump, then position the switch to SSHP. ¦ Insert the upper tabs on the thermostat body into the slot at the top of the wallplate. Press bottom of the thermostat body to snap it into the wallplate. (NOTE: Do not force the thermostat onto the wallplate, as the terminal pins may be damaged. If it does not snap properly, the thermostat may not work.) ¦ Switch on the main power at the panel or furnace. 13 PROGRAMMING Option Menu Your thermostat has many settings that can be adjusted to fit your system and preferences. ¦ Press to enter the Option Menu and to change to the next option selection. ¦ Press at any time to return to normal mode. Language Selection ¦ or to select English, Spanish, or French. Battery Status ¦ to see how much power remains in the thermostat’s battery. option ret/clear option 1 2 option Fahrenheit or Celsius (F°/C°) selection ¦ or to change the thermostat display between Fahrenheit and Celsius. 12 Hour or 24 Hour Clock selection ¦ or to change the time format display between 12 hour (AM / PM) and 24 hour (Military). SPAN selection ¦ or to change the SPAN setting to 1, 2, or 3. The factory setting is 2. Setting 1 will cause shorter cycle times. Setting 3 will cause longer cycle times. option 3 4 option 5 option Auto Season Changeover Deadband ¦ or to set the deadband between Heating and Cooling when the System Selection is set to Auto. See page 37 for more information on the Auto Season Changeover feature. 6 option Auto Recovery selection ¦ or to enable “YES” or disable “NO” the Auto Recovery Mode. The factory setting is “YES.” ¦ To change between Heat or Cool recovery modes. NOTE: Auto Recovery is one of the ENERGY STAR® features of this thermostat. Refer to the Auto Recovery section on pages 43-44 for more information. Remote Sensor Channel (does not apply to thermostat model 44660) ¦ to reach the Sensor Channel Set screen. ¦ to select sensor for RF channel setting ( for Indoor 1, for Indoor 2, or for Outdoor) 7 option 8 option sensor ¦ or to set RF communication channel (1-15) for the selected remote sensor. ¦ If you do not have, or are not using the a second or outdoor remote sensor, set the channel to - -. NOTE: The thermostat will not control your HVAC sysytem from the remote sensor set up as Outdoor . However, it is crucial that you DO NOT place remote sensor or outdoors. LCD Contrast adjustment ¦ or to change the LCD contrast between 0 and 9. Lower numbers lighten the display. Higher numbers darken the display. The factory setting is 5. 9 option Setting Time and Day Step 1 ¦ Press to enter time and day setting mode. The current hour and the AM / PM indicator will be flashing. ¦ Press to change the Hour up or down to the current hour. Note the AM / PM indicator, as the display will change at 12 AM and 12 PM. Step 2 ¦ Press again to change from hour setting to minute setting. The current minute will be flashing. ¦ Press to change the Minute up or down to the current minute. day/time or day/time or Step 3 ¦ Press again to change from minute setting to day setting. The current day will be flashing. ¦ Press to change the Day up or down to the current day. Step 4 ¦ Press again to change back to the normal display. NOTE: You may press at any time during Day and Time setting to return to the normal display. day/time or day/time or ret/clear ret/clear 12 Hr. / 24 Hr. Time Format Your thermostat is set from the factory in normal 12 (AM / PM) format. To change to 24 hour (military) time, press at any time while the Hour, Minute, or Day is flashing to toggle between the ...
Este manual também é adequado para os modelos :Os termostatos - 44660 (3.29 mb)
Os termostatos - 44008-01 (3.29 mb)
Os termostatos - 44668 (3.29 mb)
Os termostatos - 44008-01 (3.29 mb)