Follow all local electrical codes during installation. All wiring must conform to local and national electrical codes. Improper wiring or installation may damage thermostat. Recognize safety information. This is the safety-alert symbol . When you see this symbol on the equipment and in the instruction manual, be alert to the potential for personal injury. Understand the signal words DANGER, WARNING, and CAUTION. These words are used with the safety-alert symbol. DANGER identifies the most seriou

1 INSTALLATIONCONSIDERATIONS ................... 1 INSTALLATION .................................... 1 Step1—ThermostatLocation ........................ 1 Step2—InstallThermostat ........................... 2 Step3—SetThermostatConfiguration ................. 2 Step4—UnderstandThermostatOperation .............. 2 Step5—CheckThermostatOperation .................. 3 WIRINGDIAGRAMS ................................ 4 SAFETY CONSIDERATIONS Read and follow manufacturer instructions carefully. Follow a

Cooling Operation 1. Press H/C button until COOL is displayed. 2. Press DOWN button until LCD readout reads 3_/1.7_C below room temperature. Press UP and FAN buttons simultaneously to defeat timers. Cooling system should begin to operate immediately. Table 1 shows the thermostat outputs for each available stage of heating or cooling. It may be useful in checkout or troubleshooting. T1PAC/ T1PHP 3 Table 1 – Outputs T1PAC/ T1PHP EQUIPMENT HEAT CONFIGURATION EM HEAT STAGE 2 OPTION #1 Y,G,W W HP, PH

GENERAL Bryant’s 7-day, commercial, programmable thermostats are wall-mounted, low-voltage thermostats which maintain room temperature by controlling the operation of an HVAC (heating, ventilation, and air conditioning) system. Separate heating and cooling set points and auto-changeover capability allow occupied and unoccupied programming schedules for energy savings. All thermostats allow up to 4 time and temperature settings to be programmed per 24-hr period. Each thermostat stores programs fo

To ensure the schedules are properly followed, make sure that AM or PM is correct for the time chosen. When the correct time is shown, press the End button to exit the Set Time mode. V. RESET FILTER The Reset Filter function is used to clear the “Clean Filter” icon on the display screen. The Reset Filter function is initiated by pressing the Hold and Occupied buttons simultaneously. The “Clean Filter” icon reminds the user when it is time to change or clean the filter of the unit. VI. PROGRAMMIN

1 CONFIGURATION ..............................1-4 I. Thermostat Display ....................... 1 II. Heat or Cool Indicator .................... 1 III. Thermostat Front Panel Buttons ............ 2 IV. Thermostat Programming Buttons .......... 2 V. Set Clock ................................ 3 VI. Programming Thermostat Schedules ........ 3 OPERATION ................................... 5 I. Auto-Changeover ......................... 5 II. Two-Stage Operation ...................... 5 III. Clock Ba

SET THERMOSTAT TO MODE “OFF” PRIOR TO CHANGING SETTINGS IN SETUP OR RESTORING FACTORY DEFAULTS. Residential Light Commercial Systems Carrier Corporation 4/01 TSTATBBP2W01 Page 1 Front Panel Front Panel 72 70 HEAT Mo I2:00 23 4 5 1 1 2 3 4 5 Liquid Crystal Display with Thermoglow Up/Down Buttons On/Off Button Outside Button Heat or Cool Indicator Heat = Red, Cool = Green Page 2 Display Display 3 5 2 65 Night MorningDayEvening Am Pm SuMoTuWeThFrSa Setup Locked Outside Program On ONOFF COOL HEAT I2

3 4 5 Display 1 Mode Indicators Selects the operation mode of the equipment. COOL — indicates the air conditioning mode. HEAT — indicates the heat mode. AUTO — indicates the system will automatically changeover between the heat and cool modes as the temperature varies. OFF — indicates the entire system is turned off. PROGRAM ON —indicates the stored program is enabled to run. See below. 2 Clock with Day of the Week Indicates the current time and day. This clock is also used to program the timer

Improper use of heater can cause serious injury. Keep this manual for future reference. ® 200,000 BTU/HR PORTABLE FORCED AIR HEATER SAFETY INFORMATION WARNINGS IMPORTANT: Read this Owner’s Manual carefully and completely before trying to assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning. DANGER: Carbon monoxide poisoning may lead to death! Carbon Monoxide Poisoning:

The selected number is the number of degrees, plus or minus, which will be added to actual temperature. The numbers can range between - --5 and +5. Factory default is 0. Available Selection: Use UP and DOWN buttons to now move between - --5 and +5 in increments of 1. Step 4 — Thermostat Operation Temperature Display Thermostat will display room temperature until UP or DOWN button is pressed. The word SET appears when these buttons are pressed and the current setpoint is displayed. If no buttons