Assessments - 2, GPA: 5 ( )

Fabricante : Keys Fitness Arquivo Tamanho: 751.2 kb Arquivo Nome : d637fc9c-7ef5-4fb1-b13b-0b7f6bd55354.pdf Língua de Ensino:

The num-will also be required. ber in parenthesis below each part refers to the key number of the part. The second number Assembly will be more convenient if you have the refers to the quantity needed for assembly. Note: following tools: A socket set, a set of open-end or Some parts may have been pre-attached for closed-end wrenches, and a rubber mallet. shipping purposes. If a part is not in the parts bag, check to see if it has been pre-attached. M8 Acorn Nut (56)–4 Rubber Washer (51)–4 M8 x 157mm Axle (13)–2 M6 Hex Nut (54)–4 M8 Nylon Jam Nut (7)–1 M6 Flat Washer (55)–4 M8 x 1.375” Bolt (17)–1M6 x 60mm Bolt (53)–4 Plastic Washer (49)–2 Tree Fastener (45)–10 4 5 1. Before beginning assembly, make sure that you have read and understand the information on page 4. Attach one of the Stabilizers (31) to the Main Frame (1) with two M6 x 60mm Bolts (53), two M6 Flat Washers (55), and two M6 Hex Nuts (54). 3 1 31 54 55 53 1 1 45 34 54 55 1 31 53 2. Attach the other Stabilizer (31) to the Main Frame (1) with two M6 x 60mm Bolts (53), two M6 Flat Washers (55), and two M6 Hex Nuts (54). 3. Attach the Front Cover Panel (34) to the Main Frame (1) with four Tree Fasteners (45). If you can’t push the Tree Fasteners in with your fingers, tap them in with a rubber mallet. 4. Lubricate an M8 x 157mm Axle (13). Attach the Handlebar Swing Arm (5) to the Main Frame (1) with the M8 x 157mm Axle, two Rubber Washers (51), and two M8 Acorn Nuts (56). 4 1 56 51 51 56 5 Lubricate—13 2 6 7 45 45 2 21 49 10 7 11 17 5 5 6 51 56 36 Hole 1 4 51 5. Push the Magnet Bracket (36) into the hole in the Pedal Frame (4). Lubricate an M8 x 157mm Axle (13). Attach the Pedal Frame (4) to the Main Frame (1) with the M8 x 157mm Axle, two Rubber Washers (51), and two M8 Acorn Nuts (56). 6. Attach the Left Side Shield (21) to the Seat Frame (2) using three Tree Fasteners (45). If you can’t push the Tree Fasteners in with your fingers, tap them in with a rubber mallet. Attach the Right Side Shield (22, not shown) in the same way. 7. While another person holds the Long Link Arm (10) and the Short Link Arm (11) in place, put two Plastic Washers (49) between them. Then, connect the Seat Swing Arm (5), the Long Link Arm (10), and the Short Link Arm (11) using an M8 x 1.375” Bolt (17) and an M8 Nylon Jam Nut (7). 8. Remove the 1” x 2” Endcap (50) from the Seat Frame (2). Slide the Weight Saddle (8) onto the Seat Frame (2). Hook the tab on the Weight Saddle (8) into the indicated hole in the Seat Frame (2). Place the Seat (20) on the Weight Saddle (8). Slide the Seat Washer (38) onto the Seat Knob Bolt (43) and then tighten the Seat Knob (37) onto it. 8 2 Tab Hole 20 43 50 38 37 8 Lubricate—13 56 9. Depress the two buttons on the sides of the Handlebar Assembly (6) with your thumb and forefinger. Insert the Handlebar Assembly (6) into the Handlebar Swing Arm (5). Make sure that the buttons protrude through one of the two sets of holes in the Handlebar Swing Arm. The upper holes offer lower workout...

Baixe o seu

Para fazer o download, introduza 2 dígitos :