Assessments - , GPA: ( )

Instruções de Operação Impex, Modelo 831.288720

Fabricante : Impex
Arquivo Tamanho: 846.38 kb
Arquivo Nome : 3ed0f23d-bc78-47aa-b3a0-e5a04050b84e.pdf

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

2 50 48 Decal 1 1 4 5 3 4 3 28 51 45 45 1 3. Slide the Seat Carriage (4) onto the other end of the Seat Frame (3). Make sure that the Seat Carriage is oriented as shown. Insert the end of the Seat Frame into the Frame (1), and attach it with two M10 x 75mm Button Bolts (51) and two M10 Black Split Washers (45). Insert the Seat Knob (28) into the welded nut (not shown) on the right side of the Seat Carriage (4) and into one of the adjustment holes in the right side of the Seat Frame (3). Tighten the Seat Knob into the welded nut. 4. Slide a Handlebar (7) onto one side of the Seat Carriage (4). Attach the Handlebar with two M6 x 34mm Button Screws (52) and two M6 Nylon Locknuts (53). Attach the other Handlebar (7) to the Seat Carriage (4) in the same way. 4 53 7 52 7 4 2. Attach the indicated end of the Seat Frame (3) to the Rear Stabilizer (9) with two M10 x 56mm Carriage Bolts (49), two M10 Zinc Washers (62), and two M10 Zinc Nylon Locknuts (61). 61 62 3 9 2 62 49 5. Attach the Backrest Frame (5) to the Seat Carriage (4) with an M8 x 45mm Button Screw (54) and an M8 Split Washer (56) from the top, and two M8 x 37mm Button Screws (55) and two M8 Split Washers (56) from the bottom. Next, attach the Backrest (10) to the Backrest Frame (5) with four M6 x 16mm Button Screws (57). 5 10 5 57 55 56 4 54 56 6 6. Attach the Seat (12) to the Seat Carriage (4) with four M6 x 16mm Button Screws (57). 8. Identify the Left Pedal (24), which is marked with an “L.” Using an adjustable wrench, firmly tighten the Left Pedal counterclockwise into the left arm of the Crank (27). Tighten the Right Pedal (not shown) clockwise into the right arm of the Crank. Important: Tighten both Pedals as firmly as possible. After using the exercise cycle for one week, retighten the Pedals. For best performance, the Pedals must be kept tightened. Adjust the Left Pedal Strap (65) to the desired position and press the end of the Strap onto the tab on the Left Pedal (24). Adjust the Right Pedal Strap (not shown) in the same way. 27 24 Tab 65 8 7. The Console (16) requires two AA batteries (not included). Alkaline batteries are recommended. Refer to the inset drawing. Remove the battery cover from the back of the Console, and insert two AA batteries into the Console. Make sure that the negative ends of the batteries (marked “–”) are touching the springs in the Console. Reattach the battery cover. Next, plug the Reed Switch Wire (43) into the back of the Console (16). Carefully slide the Console onto the indicated tab on the Frame (1). Note: The Console is held by friction; it does not snap into place. Press the Resistance Knob (14) onto the Resistance Control (13). 1 43 14 13 16 7 6 12 57 57 57 4 9. Make sure that all parts are properly tightened before you use the exercise cycle. Note: After assembly is completed, some extra hardware may be left over. Place a mat beneath the exercise cycle to protect the floor. 16 Batteries Battery Cover 7 HOW TO OPERATE THE EXERCISE CYCLE HOW TO ADJUS...