Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
dados de dispositivos de processamento - HP 4400 Dual Controller Enterprise Virtual Array w/Embedded Switch (261.95 kb)
Facilidade de uso
NOTE:
When upgrading, the Device Addition Policy for disk groups must be set to Manual. See
“Checking the disk grouping policy” in the HP Enterprise Virtual Array Updating Product Software
Guide (XCS 11300000) for more information.
•
A full restart of both controllers is required only one time after HP P6000 Command View and
the management module software are installed on the management module of the EVA4400. This
applies when upgrading to XCS 09006000 or later. Subsequent upgrades of controller software
or management module software, or upgrading HP P6000 Command View on the management
module, do not require another full restart.
•
EVA4400s are shipped with HP P6000 Command View 9.2 or later pre-installed on the
management module within the controller enclosure (for array-based management).
•
The HP P6300/6500 EVA are shipped with HP P6000 Command View 9.4 or later pre-installed.
•
The HP P6350/6550 EVA are shipped with HP P6000 Command View 10.1 or later pre-installed.
•
You can use HP P6000 SmartStart to configure application servers.
To bypass the HP P6000 SmartStart interface and manually run the HP P6000 Command View installer,
go to the \bin\installers\CV directory on the DVD.
HP P6000 SmartStart installs HP MPIO EVA DSM, which enables you to provision storage from the
storage system; and DSM Manager, which enables you to change the default settings of HP MPIO
EVA DSM.
For more information about HP P6000 SmartStart, see the latest product release notes, available at:
http://www.hp.com/support/manuals
Under storage, select Storage Software, and then under Storage Device Management Software, select
HP P6000 SmartStart Storage Software.
SAN support
The HSV300 controller in the EVA4400 supports 2/4 Gb Fibre Channel communication, but requires
4 Gb SFPs in the controller host ports. The HSV300-S supports up to 8 Gb communication through the
embedded switch ports.
The HSV400 controller in the EVA6400 and the HSV450 controller in the EVA8400 are enabled for
4 Gb/s on each Fibre Channel host path, but will also support 2 Gb/s Fibre Channel host paths and
components for backward compatibility.
NOTE:
1 Gb path and components have specific configuration requirements. For more information
on configuration requirements and support for 2 Gb and 4 Gb EVAs, see the HP SAN Design Reference
Guide, which can be downloaded from the following website:
http://www.hp.com/go/sdgmanuals
Supported Fibre Channel switches
For complete information on which Fibre Channel switches are supported, see the Single Point of
Connectivity Knowledge (SPOCK) at http://www.hp.com/support/manuals. You must log in to access
SPOCK. If you do not already have an HP Passport account, select Register to log in on the main page
and follow the instructions.
Supported disks
For information about disk drive support, see HP P6000 Enterprise Virtual Array Disk Drive Firmware
Support, available on the HP Manuals website http://www.hp.com/support/manuals.
Under storage, click Disk Storage Systems, and then under EVA P6000 Storage, select your EVA.
SAN support
5
... Este manual também é adequado para os modelos :
dados de dispositivos de processamento - HP 4400 Dual Controller Enterprise Virtual Array (215.9 kb)
dados de dispositivos de processamento - HP EVA P6350 450GB 10K SAS Field Starter Kit (215.9 kb)
dados de dispositivos de processamento - HP EVA P6350 450GB 10K SAS FIO Starter Kit (215.9 kb)
dados de dispositivos de processamento - HP EVA P6350 900GB 10K SAS Field Starter Kit (215.9 kb)