Log:
Assessments - 5, GPA: 4 ( )

Instruções de Operação Bosch, Modelo 302D

Fabricante : Bosch
Arquivo Tamanho: 936.52 kb
Arquivo Nome : ce92fa59-d53e-e7b4-a50d-10e40d4f29e2.pdf
Língua de Ensino: en
Ir para baixar



Facilidade de uso


The wire which is coloured blue must be connected to the terminal which is marked with the letter “N” or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter “L” or coloured red. ----BLUE BROWN (NEUTRAL) (LIVE)----> Installation Before fixing the furniture door to the hood, please ensure the correct distance between the plate and the upper edge of the cabinet door (depends on the thickness of the material and whether or not there is an upper shelf) (Fig. 6). 1. Remove the grille filter C by turning the locks D and pull it out downwards (Fig. 3). 2. Take off the extendable vapour guide G (fig. 7) by turning the rear locking knobs H (Fig. 7). 3. Draw a line with a pencil on the middle of the internal side of the furnituture door (Fig. 8). 4. Fit the plate upon the internal side of the furniture door so that the line previously marked on it, is visible through the two triangles holes located on the mid upper and lower side of the plate, having care to respect the distance from the plate to the higher edge of the furniture door as for the reason mentioned above. 5. Fasten the plate to the furniture door through the 6 screws L 4,5 x 13 mm supplied (Fig. 8). 6. Replace the complete fume protection plate assembly into the extractor hood, first inserting it on its upper, then on its lower guides. 7. Turn the rear unlocking knobs H (Fig. 7) so to avoid the fume protection plate take off. 8. Replace the grille filter. 1. Remove the grille filter (Fig. 3). 2. Remove the fume protection plate (Fig. 7). 3. Mount the two hanging rails directly underneath the edge of the cupboard using three screws 4,5 x 16 mm each rail. Distance from first hole to front edge of the cupboards sides must be 153 mm (Fig. 9). 4. Push the extractor hood over the two hanging rails, then fix the hood from its inside to the cupboards sides with two screws (4,5 x 13) through the lower holes of the hood (Fig. 10). 5. Replace the the complete fume protection plate assembly into the extractor hood. 6. Replace the grille filter. • 7. Ensure that there is not a gap between the back of the hood and the wall by adjusting the spacer M tightly to the wall, using the screws O (fig. 12). Fixing the furniture door to the hood Installing the hood between cupboards with hanging rails 13 Installing the hood to the wall 14 It is possible to fix the hood in position, if necessary, by only attaching it to the rear wall. Proceed as follows: 1. Drill the four holes on the wall as indicated (Fig. 11). 2. Insert the four rawl plugs supplied into these holes. 3. Screw the two mountings hooks into the top two rawl plugs (Fig. 12). 4. Dismount the spacer M (Fig. 12) from the body of the hood by unscrewing completely the two spacer fixing screws O and washers. 5. Fix the base spacer M to the wall (Fig. 12) with the two screws R 5x45 provided (Fig. 11) using either the long or the short arm, depending on the depht ...

Este manual também é adequado para os modelos :
Fans - 302D (936.52 kb)
Fans - 302D (936.52 kb)
Fans - 302D (936.52 kb)
Fans - 302D (936.52 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias