Accumulated deposits of grease are a fire hazard. • This appliance must not be used over cook tops powered by wood or coal or in any case, over cook tops with power levels that could damage the appliance. Never use steam or high-pressure devices for cleaning your hood (regulations regarding electrical safety). • Never use the hood without the grease filters. • The minimum distance between the open down draft and the surface above it needs to be 400 mm. • When moving the down draft, never pl
Ensure that there is adequate ceiling strength and supports at the fixing points; if in doubt, consult a joiner or electrician. INSTALLATION: The extractor is intended to be operated as a re-circulation device suspended from the ceiling, as shown in Fig 11. When installing this appliance over a CDA hob, the clearance between the extractor and the hob must be equal to or exceed 650mm. This instruction overrides the instructions supplied with the CDA hob. (The height should be measured from the to
It also enables the constituent materials to be recovered, saving both energy and resources. As a reminder of the need to dispose of household appliances separately, the product is marked with a crossed-out wheeled dustbin. Please note: •Under no circumstances should the extractor be connected to any gas ventilation system, flue system or hot air ducting system. •Do not vent the extractor into an attic or loft space. •Only house the extractor in rooms with adequate ventilation. Remember that the
Replace the cover panel and refasten the sliding brackets. Fig. 2 Care and Maintenance IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. Cleaning You should use a non-abrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. You can clean you extractor effectively by simply using a dilute solution of water and mild detergent and drying to a shine with a clean clo
• Only house the extractor in rooms with adequate ventilation. Remember that the extractor is powerful and whatever air is extracted needs to be replaced. • Do not tile the extractor in. It should be removable for service or maintenance. • Do not use silicone sealant to secure the hood to the wall. • You must be able to isolate the extractor from the mains electrical supply after installation. • This extractor has been designed to be used in a room with a volume of less than 36 m3. • Steam clean
and who will comply with the I.E.E. and local regulations. The wires in the mains lead of this appliance are coloured in accordance with the following code: Blue = Neutral, Brown = Live. As the colours of the wires in the mains lead for the appliance, may not correspond with the coloured markings identifying the terminals connecting to the fused spur, proceed as follows: The wire which is coloured blue must be connected to the terminal marked N (Neutral), or coloured Black. The wire which is
Control Panel A – Light button B, C, D – Speed level buttons E – Power off button F – Timer button To switch the extractor light on or off • Press button A. To switch on the extractor or to change the speed at any time when the extractor is running • Press button B, C or D for the first, second or third speed level as required. To switch the extractor off • Press button E. The intensive function • The extractor is equipped with an intensive function which runs for ten minutes before returning to
After it has reached a height of 180 mm from the cooketop, press OFF, to stop the extraction then the Timer and after 2 sec. the OFF button. The downdraft will carry out the calibration of its aspiration panel rising and retracting for some centim- 18 eters. During this phase, the buttons on the pushbutton control panel blink. At the end of the calibration, the aspiration panel get back to the previous position and the button end to blink. Wait until the aspiration panel stops moving before r
Appliance Model Serial Number CE Declarations of Conformity: This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Gas safety, Electrical safety (LVD) and Electromagnetic interference compatibility (EMC). IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer p
3. Then lower the grease filter to remove it completely. To replace the grease filters, repeat the steps in reverse. Please note: Cleaning the grease filter in the dishwasher may lead to discolouration. This is normal and does not constitute a fault with the appliance. Changing the charcoal filter (re-circulating only) When the display flashes alternating the speed selected with the letter F, the charcoal filters must be replaced. After the charcoal filter has been replaced, the electronic memor