Nos; 5FH18AVV SFH24AW OWfiefS Guido IMPORTANT INSTRUCTIONS Retain these instructions for future reference, recid them carefully and note also the information given on the heater. IMPORTANT SAFETY INFORMATION WARNING * THE SURFACE OF THIS HEATER CAN BE HOT. The 5uncice temperatures of this heater are within the requirements of EN60-335 the European Standard covering the safety requirements of electric storage heating appliances, and momentary contact with any part of the heater should not ca

The hot interior of the heater can produce paraffin smells from polish vapours which may last for a number of hours. »DO NOT ATTEMPT TO REPAIR THE HEATER YOURSELF. In case of breakdown or other failure, switch off the heater at the wail switches and consult your supplier, local electricity company or Applied Energy Products Ltd. Always ensure that the heater is switched off at both wall switches and the fuses removed before any repair is carried out. HOW IT WORKS: This heater stores heat on

Nos: TSR12CW TSR18CW TSR24CW TSR12ACW TSR18ACW TSR24ACW C( This appliance conforms to îhe following EEC Directives: low Voltage Equipmenl Electromagnetic Compatibility 73/23/EEC 89/336/EEC 93/68/EEC 92/31 /EEC 93/68/EEC IMPORTANT NOTES: It is important to read these instructions carefully and also note the information given on the heater itself. As these particular instructions refer to the assembly and installation of a new heater, they should be retained by the installer; not left behind

Two supplies are taken into this heater, both fan heater and storage heater circuits must be connected to the same phase of the electricity supply. IF, DURING ANY REASSEMBLY OF THE HEATER, A PART OF THE THERMAL INSULATION SHOWS DAMAGE OR DETERIORATION WHICH MAY IMPAIR SAFETY, IT SHOULD BE REPLACED BY AN IDENTICAL PART WALL FIXING: The heater must ALWAYS be mounted against, and fixed to a wall as it will not stand up by itself. A detachable bracket is provided for screwing to the wall, the heate

In order to maintain stability, it is essential that the heater be placed on a level surface and care should be taken to avoid irregular surfaces, such as may result from carpets or tiled surrounds partially protruding under the heater. The heater feet are designed to go underneath a carpet rather than standing on it; this permits the weight to be taken on a firm base. Carpet gripper should be removed from behind the heater feet. BRICKS: The heater casing and the heater storage bricks with whic

skirting size is 1 5 x 120mm. Note that the smallest wall spacing should be used only when the skirting board is of the modern slim type, or there is no skirting board at all. MUST STAND VERTICAL You must fit a retaining screw at each end of the heater. 100mm {4") Skirling Goarrf —Lf'"' Outer Siol 1 SOmm i6“> Skirting Beard It THE HEATER A clear space of at least 3" (75mm) must be left at either side of the heater, and any projections or shelves must be at least 10" (250mm) above the h

If ° load rating only is required the installer should move the black wire as indicated in the circuit diagram. ELEMENT ASSEMBLY (WITH SAFETY CUT OUT) WARNING Remove the inner front panel; this carries on it's inner face the front insulation slab. Handle this with care, the insulation must not be damaged. REMOVE ALL THE PACKING CARDBOARD FROM INSIDE THE STORAGE BRICK COMPARTMENT, IF LEFT INSIDE IT WILL BE SET ON FIRE WHEN THE HEATER IS SWITCHED ON. ENSURE THAT ALL PACKAGING MATERIAL IS REMOV

When a new heater is run up to temperature/ the materials will produce a slight smell for the first few days/ these are normally harmless in a well ventilated room. It is best to make these first overnight charges with the 'Input' control knob at 'Maximum'. Caged birds, young children and people with chest ailments are best kept out of the room for this first period. output Supaslim Combi * 6 n\j 1 mm m SETTING THE CONTROLS The controls are located under the lockable flap at the right hand

Do install the hood at the correct height, allowing at least the minimum distance above a cooking appliance (see page 5). Fan Speed The right slider enables you to select the fan speed. Your Cooker Hood has three speeds to give you the correct extraction level to suit your cooking conditions. Position 1 should be selected when simmering or when using only one pan. Position 2 should be selected for normal cooking up to four pans. Position 3 should be selected when frying or cooking food with stro

Fix the wall brackets. 2. Fix the canopy hood. 3. Connect the hood to the mains supply ensuring that the canopy is functioning correctly. 4. Select the type of installation, ie. ducting or recirculation. 5. Fix the chimney stack. NOTE: The hood is more efficient in the exhaust mode, therefore, this position should be selected during the warmer months of the year when no heating is being used. When the room is being heated, if the recycle position is selected heat will not be wasted. Installing y