TO OBTAIN WARRANTY SERVICE, SIMPLY CONTACT THE NEAREST SEARS SERVICE CENTER THROUGHOUT THE UNITED STATES. This warranty applies only while this product is in use in the United States. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Sears, Roebuck and Co., D/817 WA, Hoffman Estates, IL 60179 If you want your water softener professionally installed, talk to your Sears Salesman. He will arrange for a prompt, quality installation by Sear

If you have questions when installing, operating or maintaining your softener, and when setting the timer, call this toll-free number... 1-800-426-9345 moreWater.com SAVE THIS MANUAL UltraSoft Water Softeners With DELUXE valve designed for plumbing up to 1 inch _i, Safety Guides _i, Unpacking _i, Where To Install _i, How To Install -. Tt_ / Systems Tested and Certified by NSF International against NSF/ANSl Standard 44for softener performance. _i, Pressure Testing Use the plastic bag and tie prov

2-4 Deluxe Valve SECTION2 PLAN YOUR INSTALLATION D. TYPICAL THREADED IN AND OUT PIPES TO SOFTENER If you are planning a threaded plumbing installation, with a 3-valve bypass, use the drawing in Fig. 4 as a guide. Use union fittings, as needed, to connect the plumbing. DELUXE VALVE MODELS ucets Outside So ft ":!_':_'::" :".... M (Raw W _e ater In) FITTINGS REQUIRED NOT L DENTIFIED Union (2) 90 o Elbow (2/ Pipe (as reg,) IN _ 1" NPT ,o,e _ adaptori_c°,'o_:? _o_V_o_o,_ *NOTE: For 1 in. plumbing con

• Use pipe joint compound or Teflon tape on out6, Repeat procedure on side pipe threads. outlet side. 1. Solder pipe to threaded connector, Allowto cool. Place o-ring seal on • When all piping fits together... threaded adaptor. Put ...solder all sweat fittings. adaptor into bypass ...prime and cement all PVC joints. valve port and install clip. 2. Put threaded ...tighten all threaded joints. •_ adaptor into bypass valve port. [] CAUTIONS: • Never solder fittings while connected to nonmetallic pa

__ (included with some models) // I \ NOTE: / \ For plumbing connection, buy 2 \ To connect to 1-1/4" sweat adaptors and plumb directly to To connect to 1-1/4" copper household the inlet-outlet adaptors or bypass copper household / valve. Threads on the inlet-outlet plumbing / _. plumbing _ adaptors and bypass valve are 1" NPT. \f CAUTION: Available from Sears DO ALL SOLDERING BEFORE see Owner's Manual for part numbers Available from Sears CONNECTING SWEAT ADAPTOR see Owner's Manual for part num

SANITIZE YOUR WATER SOFTENER AS FOLLOWS: 1. Be certain the bypass valve is pulled out to “service” position. 2. Lift the salt hole cover and using a pail add up to 3 gallons of water to the salt storage tank. 3. Remove the brine well cover (Fig. 28) and pour about 3/4 ounce, or 1 to 2 tablespoons, of common 5.25%1, unscented, household bleach (Clorox, Linco, BoPeep, White Sail, Eagle, etc.) in the softener brinewell. Replace the brinewell cover. 4. Press the REGENERATION button and hold for 3 se

Without brine, the resin bed does not regenerate and you will have hard water. If the storage tank is full of salt, it is hard to tell if you have a salt bridge. Salt is loose on top, but the bridge is under it. The following is the best way to check for a salt bridge. Salt should be loose all the way to the bottom of the tank. Hold a broom handle, or like tool, up to the softener as shown in Fig. 41. Make a pencil mark on the handle, 1'' or 2'' below the top height of the rim. Then, carefully p

(May recharge more often using smaller salt dosage and less water). When installing this unit in the State of California, this setting MUST be ON. FIG. 34 California Efficiency Requirement Your Kenmore Water Softener has a “High Efficiency” feature with an “ON” or “OFF” setting. This softener setting is shipped in the “OFF” position, which utilizes the maximum rated capacity while most often achieving maximum salt efficiencies. When installing this unit in the State of California, you MUST turn

6. Pull valve through hole with pliers or a valve tool (available at your local filling station or Automotive Center). 7. Follow steps 14 through 20 under "Vinyl Bag Removal" to reinstall bag in tank. Testing for Bag Leakage 1. Follow steps 1 through 4 under "Vinyl Bag Removal". 2. Tip tank on end, valve down. Be careful not to break valve! 3. If bag leaks, water wll] run out of valve. If so, replace bag as instructed above. MAINTENANCE DISASSEMBLY AND ASSEMBLY OF PUMP AWARNING] Risk of electric

[_eck Valve I Steel Drive Pipe Drive coupling Well point Liven poi!It For a pump at sea level mounted directly over the well, be sure the total lift from the pumping water level to the pump does not exceed 20 feet. This will be less ff the pump is off set from the well. The maximum lift of any pump decreases at the rate of about 1" less lift for every 1,000 feet of elevation above sea level. For example, at Denver, Colorado (Elev. 5,000') the pump loses five feet of lift. The maximum depth from