Follow all steps exactly to correctly install. Failure to follow them could cause personal injury or property damage. Reading this book will also help you to get all of the benefits from your water filter. • Your water filter will improve your water as described on page 11. It will not soften water or remove iron. It will not purify polluted water or make it safe to drink. Also see the specifications on page 18. • Protect the filter and piping from freezing. Damage from freezing voids the filter

Locate clamp A (turn handle in to align pin if pre- drilled hole) and clamp B on the pipe. Fasten in place using 2 screws. Tighten each screw evenly, STEP 2 --INSTALL THE • Before beginning, be sure to read the note on page 5. • The drain adapter fits 1-1/2" sink drain pipe. • The adapter installs directly onto the s(nk tailpiece as typically shown in fig. A and B. • Locate so drain tubing from the faucet (FIG. 7, page 10) makes a straight run to the adapter, without dips, loops, low spots or ki

If you have questions when installing, operating or maintaining your softener, and when setting the timer, call this toll-free number... 1-800-426-9345 M-F,7am -8pm, CST For repair or replacement parts, call this toll-free number... 1-800-366-7278 See back cover for other Sears service numbers. SAVE THIS MANUAL Sears, Roebuck and Co., PRINTEDIN U.S.A. UltraSoft Water Softeners with High Performance _i,Warranty Valve _i, Start Up / Setting _i, How It Works Timer _i, Care Of _i, Specifications _i,

__ (included with some models) // I \ NOTE: / \ For plumbing connection, buy 2 \ To connect to 1-1/4" sweat adaptors and plumb directly to To connect to 1-1/4" copper household the inlet-outlet adaptors or bypass copper household / valve. Threads on the inlet-outlet plumbing / _. plumbing _ adaptors and bypass valve are 1" NPT. \f CAUTION: Available from Sears DO ALL SOLDERING BEFORE see Owner's Manual for part numbers Available from Sears CONNECTING SWEAT ADAPTOR see Owner's Manual for part num

8) at a fast rate to flush iron minerals, dirt and sediments from the bed and to the drain. The bed lifts and expands for good cleaning. Water Flow Through the Softener in Backwash hard water hard water bypass OUT t fIN drain resin bed lifted and expanded [] FAST RINSE: Backwash is followed by a fast flow of water down through the resin tank. The fast flow packs the resin bed and gets it ready for return to service (FIG. 9). After fast rinse, the softener returns to service. Hard water goes into

to conform before doing maintenance on the Reverse Osmosis system. Correction: Send treated and untreated water samples to a water analysis lab for testing. It is important to test both the treated and untreated water to determine system performance. If the TDS is not within the system's performance guidelines, replace the prefitter, post fitter and RO membrane cartridges. Cause: Missing flow control insert in red drain tube [Correction: Replace flow control insert. See page 21. or its correspon

625.348321 Caution: OWNER’S MANUAL MODEL NO. 625.348321 Caution: Read and Follow All Safety Rules and Operating Instructions Before First Use of This Product. If you have questions when installing, operating or maintaining your softener, and when setting the timer, call this toll---free number... 1- ---800- ---426- ---9345 SAVE THIS MANUAL Solid State Water Softener z Warranty z Start Up / Setting Timer z How It Works z Care Of / Troubleshooting z Specifications z Repair Parts Use plastic bag an

Please note that there are two gaskets provided with the dlverter. Use the thick gasket. Thread the Dlverter Valve onto the faucet "hand-tight* only, (See Figure B.) Do not overtlghten! Overtlghten ing can damage the threads. If the dlverter will not thread on properly, use the thin gasket, If the Diverter Valve is not compatible, an Adapter and Gasket Kit is provided to obtain a proper fit, (See Figure 1.) B. To run water through the filter, turn on the COLD WATER faucet and slide the dlverter

Carefully push into the bridge in a few places to break it. Do not try to break the salt bridge by pounding on the outside of the salt tank. You may damage the tank. If the wrong kind of salt was the cause of the bridge, take it out. Then fill the tank with nugget or pellet salt only. FIG. 9 SALT BRIDGE 14 SECTION 3 CARE OF YOUR SOFTENER 3B. KEEPING THE WATER SOFTENER CLEAN COVERS To keep your new Sears water softener looking nice, apply a coat of paste wax and repeat once a year. When

If an Error code shows, the SELECT button to enter the diagnostic 1. Press the ON/OFF-HOLD button and 3 seconds. *RECHARGE and Fill begin first press display. hold in for to flash as the softener enters the fill cycle of regeneration. When Fill is on steady, remove the brinewell cover and, using a flashlight, observe fill water entering the tank. *NOTE: If the CLEAN feature is set to ON, a cleaning backwash ((,ZEAN and Bkwsb orRinse flashes in the display, along with the minutes of the clean cyc