The sound is not balanced because the distance between the listening position and the various speakers is different. The difference in distance between the front left speaker and the rear right speaker is 1.75 m (68-7/8"). Time correction eliminates the differences in the time required for the sound to reach the listening position. The time of the front left speaker is corrected by 5.1 ms so that its sound reaches the listening position at the same time as the sound of other speakers. Example 2.

Using such accessories can cause the disc to be out of standard specifications and may create operational problems. We recommend not using these accessories on discs played in Alpine CD players. Transparent Sheet Disc Stabilizer 3-EN Basic Operations POWER BAND 2 MODE / LOUD c g DN f UP Detaching the Front Panel 1 Press and hold the POWER button for at least 3 seconds to turn off the power. 2 Press the (Release) button at lower left corner until the front panel pops out. 3 Grasp the left side of

Failure to do so may result in an accident. KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISES WHILE DRIVING. Excessive volume levels that obscure sounds such as emergency vehicle sirens or road warning signals (train crossings, etc.) can be dangerous and may result in an accident. LISTENING AT LOUD VOLUME LEVELS IN A CAR MAY ALSO CAUSE HEARING DAMAGE. MINIMIZE DISPLAY VIEWING WHILE DRIVING. Viewing the display may distract the driver from looking ahead of the vehicle and cause a

4 Within 10 seconds, press and hold -/J for at least 2 seconds to erase the title displayed. 5 Press TITLE to cancel the title erasing mode. • You cannot erase CD-TEXT. • "TITLE NO DATA" ("NO DATA") is displayed for 2 seconds if the title is not input in step 2, or if all titles are erased in step 4. Displaying Time Press TITLE repeatedly until the time is displayed. Each press changes the display. For details, see “Displaying the Title/Text” (page 22). • Selecting any tuner or CD function while

1 Press and hold /ESC for at least 2 seconds to activate the Quick Search mode. 2 Turn the Rotary encoder to select a desired song. The selected song is played back immediately. • Press and hold /ESC for at least 2 seconds in the search mode to cancel. Or, the search mode is canceled if no operation is performed for 10 seconds. • If many songs are in the iPod, it takes time to search for songs. • If any one of the preset buttons (1 through 6) is pressed in the search mode, a search can be made q

3 Grasp the front panel firmly, slide to the left , and then pull to remove. • The front panel may become hot in normal usage (especially the connector terminals on the back of the front panel). This is not a malfunction. • To protect the front panel, place it in the supplied carrying case. • When detaching the front panel, do not apply excessive force as it may result in malfunction. • Do not leave the front panel open, or drive the car with the panel open as it may result in an accident or mal

• MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. • MANUAL DE OPERACION Lealo antes de utilizar este equipo. ALPINE ELECTRONICS, INC. Tokyo office: 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-8501, Japan Tel.: (03) 3494-1101 ALPINE ELECTRONICS OF AMERICA, INC. 19145 Gramercy Place, Torrance, California 90501, U.S.A. Tel.: 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF CANADA, INC. Suite 203, 7300 Warden Ave. Markham, Ontario L3R 9Z6, Canada Tel.: 1-800-ALPINE-1 (1-800-257-4631

CDA-7876 Only NOTE If you press the g DN button the display scrolls in reverse sequence. 6-EN 3 Press the TUNE button to toggle mode between SUB-W ON and SUBW OFF. 4 Press the SETUP button after setting the SUB-W ON. 5 Press the MODE button repeatedly to select the SUB-W mode. > SUB-W > BALANCE VOLUME < FADER < Press the g DN or f UP button after selecting the SUB-W mode, and the subwoofer output phase is toggled SUBW NOR (0°) or SUBW REV (180°). 6 Rotate Audio Control knob until the desired sou

This mode is useful if you feel the unit's backlighting is too bright at night. Scroll Type Setting Scroll Type 1 / Scroll Type 2 (Initial setting) Two types of scroll can be selected. You can select the scroll type you like. Scroll Type 1 : The characters scroll sequentially, appearing from the right side of the display. Scroll Type 2 : The characters are displayed one by one, and disappear one by one from the left side of the display after the screen is filled up with the characters. Scroll Se

4 Press the SETUP button to return to normal mode. Setting the Defeat Mode External Interrupt SPEAKER RIGHT FRONT SPEAKER RIGHT REAR SPEAKER LEFT REAR SPEAKER LEFT FRONT When interrupting external devices to this unit, turning DEFEAT ON will bypass BASS, TREBLE and MX for the external interrupt. 1 Press and hold the SETUP button for at least 3 seconds. 2 Press the f UP or g DN button to select the INTERRUPT mode. 3 Press the BAND button to toggle the mode between ON and OFF. When using Initial m