• Do not attempt to clean this unit with chemical solvents as this might damage the finish. Use a clean dry cloth. • Operate controls and switches as described in the manual. • Before turning on the power, make certain that the connecting cords, if any, and power cord are properly installed. • Store your CDs in a cool area to avoid damage from heat. • When moving the set, be sure to first disconnect the AC power cord. FCC INFORMATION This equipment has been tested and found to comply with the li

"PROG" indicator and Program No. "P -01" appears. 2.) Press or button until the first track to be programmed appears in the display. Example: Track # 7. 3.) Press the MEMORY button again to enter the selected track in the memory. The track indicator returns to a "00" and the Program No. advances to "P -02". 4.) Repeat Steps 2 and 3 until you have entered up to a total of 24 tracks in the memory. 5.) Press the Play/Pause button to begin programmed playback. The “PROG” indicator remains in the dis

To allow recording, the record protection tag on the disc must be in the correct position. RECORDING FROM MONO INTERNAL MIC 16 17 • RECORD Start recording • PAUSE, RECORD Record pause followed by PAUSE Start recording 4. Adjust the recording levels so that the peak level meters do not go beyond 0dB (marked ‘OVR’ in the top right of the diagram below). If the recording level goes above 0dB, distortion to the recorded material may occur. 5. Press the STOP button to stop recording. Or press the PAU

•Carefully remove any small strips of tape which may have been used to keep the CD and Cassette doors closed during shipment. •Open the CD compartment by lifting up the OPEN/CLOSE tab on top panel. Inside the CDcompartment you will see a “dummy”CDprotection card which is used to prevent the laser pick-up from moving during shipment. Carefully remove this card and close the CD compartment door. •Please save the carton and packing materials in the event that your unit ever needs to be returned for

SKIP REV. HD8150_122904.p65 6 29/12/2004, 9:51 7 1.) OPEN Switch – Slide to the right to unlock and open the CD door. 2.) VOLUME Control – Raises or lowers the volume. 3.) PHONES Jack – Connect stereo headphones, included, to this jack. 4.) HOLD Switch (Bottom Cabinet). 5.) PROG (Program) Button. 6.) PLAY/PAUSE Button. 7.) SKIP REV Button. 8.) SKIP FWD Button. 9.) LCDDisplay – Shows Track number, Playing time, Anti-Skip status, Program, Repeat, Shuffle, and Intro modes. 10.) ESP Button. 11.) MOD

3.) SHUFF (Shuffle) Indicator – Appears when Random playback mode is selected. 4.) INTRO Indicator – Appears when Intro playback mode is selected. 5.) HOLD Indicator – Appears when HOLD switch is set to ‘On’position. 6.) (Repeat 1) /ALL Indicators – Appears when the Repeat playback mode is selected. 7.) Battery Status Indicator – Appears when battery level becomes low. 8.) Elapsed Time (Seconds) Display. 9.) Elapsed Time (Minutes) Display. 10.) ANTI-SHOCK Indicator – Indicates ESP Protection is

MHzFM POP MEMORYCH STEREO MHzFM POP CH STEREO 4.) The unit can store up to 20 FM stations, 20 AM stations. TUNING TO A PRESET STATION Select the desired station preset number by pressing the REPEAT / MEMORY UP button. 8 ES27_ib_drafts.p65 8 19/3/2002, 16:09 ANTENNA FM For FM reception there is a built-in 3 ft FM antenna wire at the rear of the unit. Unravel the wire and move it around to obtain the best reception. AM This system includes an external AM Loop antenna. Assemble the AM loop antenna

2.) AUX / TUNER-BAND / MONO-ST / EQ / X-BASS Buttons. 3.) CD Door. 4.) DISC 1 Tray. 5.) DISC 2 Tray. 6.) DISC 3 Tray. 7.) MUTE Button. 8.) VOL-DOWN / VOL-UP Buttons. 9.) CD Door OPEN/CLOSE Button. 10.) DISC 3 Indicator & Play Button. 11.) DISC 2 Indicator & Play Button. 12.) DISC 1 Indicator & Play Button. 13.) SKIP + ( ) Button. 14.) PLAY/PAUSE Button. 15.) STOP Button. 16.) SKIP – ( ) Button. 17.) MULTI FUNCTION DISPLAY. 18.) Remote SENSOR. 19.) Pedestal Stand. 20.) PROGRAM Button. 21.) REPEAT

3.) Use the / buttons to select the first track to be programmed. (Example: Track 08). 4.) Whentrack number“08”flashes inthedisplay,press the PROGRAM button once again to enter the track “08”inprogram memorynumber “01”.Track number “08” disappears and program memory number returns to “00”, indicating that you may now select a track to be entered in program memory number “02”. PROG PROG PROG 5.) Use the / buttons to select the next track to be programmed. When the desired track number appears in

13 NR40_110804.p65 13 8/11/2004, 10:05 Programmed Playback This feature allows you to program up to 20 tracks on a disc for playback in any desired order. Note: You can program tracks while the disc is stopped or while the disc is playing. PROGRAM 1.) Press the PROGRAM button to enter the Program Mode. The Program number briefly shows ‘0 1’, then ‘0 0’ and the PROGRAM indicator flash. PROGRAM 2.) Press the F.SKIP or B.SKIP buttons to select the first track number you wish to enter in the program