SERvICE a. by qualified repair personnel. b. When servicing a tool, use only identical replacement parts. Use only authorized parts. c. Use only the lubricants supplied with the tool or specified by the manufacturer. the tool without first obtaining written approval from Campbell Hausfeld. Do not use the tool if any shields or guards are removed or altered. Do not use the tool as a hammer. Personal injury or tool damage may occur. AIR SOURCE a. Never connect to an air source that is capable of e

Always remain in a firmly balanced position when using or handling the tool. Avoid long extended periods of work with the tool. Stop using the tool if you feel pain in hands or arms. i. Never point an air tool at oneself or any other person. Serious injury could occur. j. Do not put hands near or under moving parts. TOOL USE AND CARE a. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against the body is unstable and is abl

After an air tool has been lubricated, oil will discharge through the exhaust port during the first few seconds of operation. Thus, THE EXHAUST PORT MUST BE COVERED WITH A TOWEL before applying air pressure. FAILURE TO COVER THE EXHAUST PORT CAN RESULT IN SERIOUS INJURY. 4. Connect the impact wrench to the air supply and cover the exhaust port with a towel. Run the impact wrench in both the forward and reverse directions for 20 to 30 seconds. Oil will discharge from the exhaust port when air pre

...................................................... ............................................................ A i r T o l s Air Tools • 130 ft. lbs. ultimate torque • 1,200 impacts per minute • Patented single impact mechanism provides 20% more working torque • Balanced, compact, ergonomic design for increased comfort 3/8” Impact Wrench TL1149 • 250 ft. lbs. ultimate torque • Built-in power regulator to control speed and torque • Push button forward/reverse valve for fast change of directi

Allow the bit to strike the bottom of the chuck. Center the bit in the chuck jaws and tighten the jaws by hand to align the bit. 3. Place the chuck key into each of the three holes in the chuck, turning it clockwise to tighten the chuck securely. NOTE: Never use a wrench or means other than a chuck key to tighten or loosen the chuck. 4. To remove the bit, unplug the tool, insert the chuck key into one of the holes in the chuck and turn it counterclockwise. Be sure that the shank of the bit and t

• Do not attempt to repair power cord. PERSONAL SAFETY Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for

la rueda se doble o se pueda quebrar. Instalacion / Remocion de la hecho, la luz roja “ON” (encendido) the reach of children and do The guard protects the operator g) If devices are provided for • Una vez completada la operacion de bateria de la herramienta de carga deberia encenderse en not allow persons unfamiliar from broken disc fragments. the connection of dust corte, retire la herramienta de la lugar de la luz verde “OFF”. Esta luz with the power tool or these m) Make sure that the guard i

al target level Vertical Target level • Snap-on storage case Model # Voltage Battery Type RPM Switch Torque (lbs) Battery Pack DG111200CK 12.0 NiCD 0-600 Variable 190 Removable DG111400CK 14.4 NiCD 0-600 Variable 190 Removable /-« CAMPBELLL 4 HAfJSFEW* visit us online: Cordless Drills Cordless drill, 6 Volt alkaline Cordless drill, 9.6 Volt ' Convenient onboard access to driver bits • Barrel level for horizontal drilling accuracy • Change drill and driver bits in a snap. Hex shaft

42mm DC motor to complete large tasks faster and easier • LED light panel for low battery warning. Magnetic tray secures metal objects for instant access. Barrel level for horizontal drilling accuracy • Convenient onboard access to four driver bit sizes • No key required for tightening • Faster bit changes • Lightweight 2 TIMES THE POWER Campbell Hausfeld Other Brands 42mm Motor 36mm Motor • Dual speed switch • Magnetic tray • Horizontal target level • Low battery light Vertical Ta

42mm DC motor to complete large tasks faster and easier • LED light panel for low battery warning. Magnetic tray secures metal objects for instant access. Barrel level for horizontal drilling accuracy • Convenient onboard access to four driver bit sizes • No key required for tightening • Faster bit changes • Lightweight 2 TIMES THE POWER Campbell Hausfeld Other Brands 42mm Motor 36mm Motor • Dual speed switch • Magnetic tray • Horizontal target level • Low battery light Vertical Ta