48550 For Derby Pacer 1334 Kit Contents: Ref Part No. Qty. Description A. 1724832 1 MULCH PLATE B. 1724457 1 34” BAFFLE C. 1923362 1 NUT, Hex Lock, 5/16-18 D. 1679163 1 WING NUT E. 1724475 1 J-BOLT F. 25127 5 NUT, Serrated Flange, 5/16-18 G. 1931333 5 CARRIAGE BOLT, 5/16-18 3/4 O ii /• i ~ A fr "'n -V t'r"} y / Figure 1. Kit Components © Copyright 2003 Ferris Industries. All Rights Reserved. 1 48551 Rev. 01/2003 TP 200-7115-00-SK-D Installation Instructions 34” Mulching

This kit should be installed when using the Triple Bagger Grass Collection System. Kit Contents: Ref Part No. Qty. Description 1 22467 2 Oil Cooler 2 1846152 1 Mount Bracket-Left 3 1846153 1 Mount Bracket-Right 4 1846154 1 Oil Cooler Mount 5 22106 2 3/8” Hose Fitting 6 21164 4 Hose Clamp 7 25299 8 Bolt, 1/4-20 x 3/4” Torx Head 8 25095 8 Nut, 1/4-20 Nylon Lock 9 50860-19 1 3/8” Hose, 19” (not shown) 10 50860-25 1 3/8” Hose, 25” (not shown) 11 50860-48 2 3/8” Hose, 48” (not shown) 12 50862-18 1 3/

See Figure 4 for the proper hose locations. Secure with the enclosed hose clamps. 18. Install the tie wraps as shown in Figures 4-6. Use a long tie wrap to secure the 48” hoses to the 5/8” supply hose. Position the hoses so the do not contact the battery pan. Use the remaining two long tie wraps the bundle the hoses together in front of the engine. Be sure the tie wrap the hoses to the engine screen. Use the short tie wrap to secure the 25” hose to the engine oil dipstick tube. Do not overtighte

1846261 © Copyright 2000 Ferris Industries. All Rights Reserved. 1 Rev. 9/2000 TP 200-7030-00-SL-D Figure 1. Kit Contents 1 4 32 8 7 6 5 Figure 2. Fitting Orientation Installation Instructions 1846197 7. Block the front wheels and jack up the rear of the machine and set on jack stands or wooden blocks. Remove the left drive tire. This will allow for easier access to the left hand pump. 8. Remove the left return hose and loosen the jam nut on the fitting on the pump. Rotate the fitting towards th

Residual dirt and grass is easily removed immediately after mowing. 1. Remove grass deposits with a brush and a cloth. 2. Oil the red cutting mechanism lightly with thin oil (e.g. sprayed oil). 7. Troubleshooting DANGER! Cutting tool can cause injuries! V Wear suitable work gloves when rectifying faults. 10 Fault Possible Cause Rectification Abnormal Noises Screws / components loose v Tighten screws Foreign bodies on the blade. v Remove foreign bodies. Notch in the blade v Remove notches with gr

9 GB Adjusting the cutting height: 566 The cutting height can be set to any position between 12 mm and 42 mm. 1. Stand behind the cylinder mower with one foot on the roller 5. 2. Release the two locking screws 6 and adjust to the correct height in the inspection window 7. 7 3. Tighten the two locking screws 6 on both sides to the same height. The locking screws 6 must always be set to the same height on both sides. The mower may only be adjusted to a depth in which the lower blade does not touch

v Insert the key into the socket. Circuit breaker has been triggered (Red Error-LED flashes). v Wait approx. 5-10 minutes then turn on the mower again. Tab on Accu loose. v Open the cover and push the tab receptacle onto the tab. Full discharge protection has responded. v Charge Accu. Motor jams and is noisy Blocked by foreign body. Blocking protection activated. (Red Error-LED flashes). 1. Switch off mower, 2. Remove key. 3. Remove foreign body. Cutting load too high. v Reduce mowing speed and

keit erst nach mehreren Lade- A Vor dem Einstellen oder Saubern ist der Motor- Ist der Accu vollig entladen, maher auszuschalten und z. B. durch lang andauernde gegen unbeabsichtigtes Ein- Lagerung ohne zwischenzeitschalten zu schutzen. Dazu ist liche Nachladung, dann ist der Schlusselschalter Q aus die volle Accu-Kapazitat erst der Kontaktbuchse des Motor- nach mehreren Lade- / Entlademahers zu ziehen. vorgangen wieder verfugbar. 7.2 Der Accu (Abb. E/ G) Laden des Accus temperatur oder Aufheizu