Assessments - 3, GPA: 4.3 ( )

Fabricante : Friedrich Arquivo Tamanho: 1.98 mb Arquivo Nome : Língua de Ensino:

Do not under any circumstances cut or remove the grounding prong from the plug. Power supply cord with 3-prong grounding plug Perpendicular type Standard 250V, 3-wire grounding receptacle rated 20A, 250V AC Use 20 AMP time delay fuse or circuit breaker. Refer to the nameplate for correct fusing. All wiring should be made in accordance with local electrical codes and regulations. NOTE : Aluminum house wiring may pose special problems. Consult a qualified electrician. ELECTRICAL SAFETY IMPORTANT GROUNDING INSTRUCTIONS 208, 230, and 208/230 VOLT UNITS Air conditioner has a three-prong grounding plug These units are equipped with a three-prong on its power supply cord, which must be plugged grounding plug on the power supply cord, which into properly grounded three-prong wall must be plugged into a matching, properly receptacle for your protection against possible grounded three-prong wall receptacle for your shock hazard. protection against possible shock hazard. If such an outlet is not present, one must be installed by a FUSE – Use a time-delay fuse or circuit breaker. qualified electrician in accordance with the National Refer to the nameplate for proper power supply Electrical Code and local codes and ordinances. requirements. Electrical Data 5 About the Controls on the Air Conditioner The controls will look like one of the following: About the Controls onthe Air Conditioner Controls – Cooling Only Models Off - Turns air conditioner off. Med Fan Only - Med speed fan operation without cooling. Low Fan Only - Low speed fan operation without cooling. High Cool - Cooling with high speed fan operation. Med Cool - Cooling with med speed fan operation. Low Cool - Cooling with low speed fan operation. This automatically controls the temperature of the indoor air. Turn the knob clockwise for greater cooling. Turn the knob counter-clockwise for more moderate cooling. • FOR NORMAL COOLING 1. Turn the MODE Knob to the Med Cool setting. 2. Set the Temperature Knob to the desired temperature (the mid-point is a good starting position). If the room temperature is not satisfactory after a reasonable time, adjust the control to a cooler or warmer setting, as appropriate. • FOR MAXIMUM COOLING 1. Turn the MODE Knob to the High Cool setting. 2. Set the Temperature Knob to the coolest temperature setting all the way to the right. • FOR QUIETER OPERATION 1. Turn the Operation Knob to the Low Cool setting. 2. Set the Temperature Knob as needed. 6 The controls will look like one of the following: Controls – Cooling & Heating Off - Turns the air conditioner off. Fan Only - The low fan speed operation without cooling/heating. Low Cool -Cooling with the low speed fan operation. High Cool -Cooling with the high speed fan operation. Low Heat -Heating with the low speed fan operation. High Heat -Heating with the high speed fan operation. Turn the Temperature Knob to the desired setting. The central position is a normal setting for average conditions. You can change this setting, if necessary, in accordance with your temperature preference. The thermostat automatically controls cooling or heating, but the fan runs continuously whenever the air conditioner is in operation. If the room is too warm, turn the thermostat control clockwise. If the room is too cool, turn the thermostat control counterclockwise. The compressor will turn on and off to keep the room at the set temperature. In the heating operation, the electric heater will turn on and off to keep the room at the set temperature. A slight burning odor may come from the CAUTION When the air conditioner has been operated in unit when first switching to HEAT after the the cooling or heating mode and is turned off or cooling season is over. This odor, caused set to the fan position, wait at least 3 minutes by fine dust particles on the heater, will before resetting to the cooling operation again. disappear quickly. This is normal operation. About the Controls on the Air Conditioner 7 About the Controls onthe Air Conditioner About the Controls onthe Air Conditioner Additional controls and important information. Ventilation Control Push the lever to the "CLOSE" position to cool, heat or recirculate room air only. Pull the lever to the "OPEN" position to exhaust smoke or stale air from the room. This feature is best used in conjunction with the FAN ONLY position. Air Direction PULL OPEN / PUSH CLOSE The direction of air can be controlled by adjusting the horizontal and vertical louvers. • HORIZONTAL AIR-DIRECTION CONTROL The horizontal air direction is adjusted by moving the vertical louver. The lever for the vertical louver is located in the right and left side of the air discharge. • VERTICAL AIR-DIRECTION CONTROL The vertical air direction is adjusted by moving the horizontal louver. 8 9 About the Controls on the Air Conditioner Air Filter Cleaning The air filter should be checked at least twice a month to see if cleaning is necessary. Trapped particles in the filter will build up a...

Baixe o seu

Para fazer o download, introduza 2 dígitos :