Assessments - 4, GPA: 4.5 ( )

Fabricante : Friedrich Arquivo Tamanho: 1.98 mb Arquivo Nome : Língua de Ensino:

This reduces the cooling capacity and can also cause an accumulation of frost on the cooling coils. If the filter becomes torn or damaged you should replace immediately. Replacement filters are available from your salesperson, dealer, and the authorized customer service centers. 1. Open the inlet grille downward by grasping the top outside edges of the inlet grille and pulling it towards you. 2. Remove the air filter from the front grille assembly by pulling the air filter up slightly. 3. Wash the filter using lukewarm water and a mild detergent. 4. Gently shake all excess water from the filter. Make sure the filter is completely dry and replace the filter back into the unit. How to Attach Front Grille to Cabinet The front grille can be removed for cleaning or to check the model and serial numbers. For your safety, you should attach the front grille using the following procedures. Care and Maintenance 1. Pull down front grille from the cabinet top. 2. Push front grille’s tips toward the cabinet in order to insert front grille’s tabs into the cabinet. 3. Open the inlet grille. 4. Tighten the screw through the front grille into the plate of control box. 5. Close inlet grille. TURN THE AIR CONDITIONER OFF AND REMOVE THE PLUG FROM THE POWER OUTLET. 10 Features Features and Installation 1 5 7 3 6 2 4 11 8 9 10 13 14 12 15 17 16 Learning part name prior to installation will help you understand the installation procedure. Features The Unit The Sleeve with the Rear Grille (sold separately) 1. CABINET 2. HORIZONTAL AIR DEFLECTOR (Vertical Louver) 3. VERTICAL AIR DEFLECTOR (Horizontal Louver) 4. AIR DISCHARGE 5. FRONT GRILLE 6. INLET GRILLE (Air Intake) 7. AIR FILTER 8. CONTROL BOARD 9. KNOBS 10. POWER CORD 11. EVAPORATOR 12. CONDENSER 13. COMPRESSOR 14. BASE PAN 15. BRACE 16. SLEEVE ASSEMBLY (Including Expanded Aluminum Rear grille) 17. REAR GRILLE Installation Remove packing sheet from the back of the sleeve, and packing corner and blue tape from the air conditioner. INSTALLATION REQUIREMENTS If you use an existing wall sleeve, you should measure its dimensions. Install the new air conditioner according to these installation instructions to achieve the best performance. All wall sleeves used to mount the new air conditioner must be in good structural condition and have a rear grille to securely attach the new air conditioner. (FIG. 1) With the FRIEDRICH USC sleeve, you can maintain the best performance of the new air conditioner. (FIG. 2) 14-13/32" (366 mm) 24-21/32" (626 mm) 18"(458 mm) 19-21/32" (499 mm) FIG. 1Air Conditioner 15-17/32" (394 mm) 16-23/32" (425 mm) 25-7/8" (656 mm) Expanded aluminum metal grille FIG. 2FRIEDRICH Wall Sleeve INSTALLATION HARDWARE 1 8 4 5 6 7 3 2 2 Size options 2 Size options ITEM NAME OF PARTS Q'TY 1 PLASTIC GRILLE 1 2 HORIZONTAL INSULATION STRIPS 2 3 AROUND INSULATION STRIPS 2 4 SUPPORT BLOCK 2 5 BAFFLE 1 6 TRIM FRAME 2 7 SHIM 2 8 PLASTIC NUTS AND WASHER SCREWS 4 ELECTRICAL SERVICE Check your available electrical service. The power supply available must be the same as that shown on the unit nameplate (found on left side of cabinet). All models are equipped with a 3-prong service plug to provide proper service and safe positive grounding. Do not change plug in any way. Do not use an adapter plug. If your present wall outlet does not match your plug, call a qualified electrician to make the necessary corrections. SAVE CARTON for storage and this OWNER'S MANUAL for future reference. The carton is the best way to store unit during winter or when not in use. To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed: • Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit. • Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over an extended period of time. • Handle air conditioner with care. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. • Make sure air conditioner does not fall during installation. CAUTION REQUIRED TOOLS: • 3/8-inch open end wrench or adjustable • Tight Fitting gloves • Standard screwdriver wrench • Phillips screwdriver • 1/4-inch hex socket • Pliers and ratchet • Sharp knife • Tape measure • Electric drill • 1/4-inch drill bit Features and Installation 11 Features and Installation INSTALLATION We strongly recommend the removal of the old wall sleeve and the installation of a new FRIEDRICH USC Wall Sleeve. If you decide to keep the existing wall sleeve, you have to redirect the louvers at the back of the wall sleeve illustration. The use of pliers is recommended. If you DO NOT redirect, you run the risk of poor performance or premature product failure. This is not covered under the terms of the FRI...

Baixe o seu

Para fazer o download, introduza 2 dígitos :