Fill water tank again and repeat basic operations previously outlined. yWARNINGy IMPROPER USE OF THE GROUNDED PLUG CAN RESULT IN THE RISK OF ELECTRICAL SHOCK. IF THE POWER CORD IS DAMAGED, HAVE IT REPLACED BY AN AUTHORIZED AVANTI PRODUCTS SERVICE CENTER. OPERATING YOUR WATER DISPENSER > Steps to replace water bottles • Use a clean cloth to wipe off neck of bottle. • Remove cap. • Carefully lift bottle (approx. 40 lbs.) using your legs and not your back. Do not place hands in opening of b

Make sure that you use an appropriate dust collection system connected to your shaper. You may have to create or modify other shop ducting to achieve the correct dust collection system clearances and airflow. Connect a 3" flexible dust collection hose to the rear of the fence adjustment tube. Use a 3" hose clamp to secure the hose to the tube. See Figure 11. Figure 11. Dust collection connection. Connect DuctingHere Fence Adjustment Tube For additional information on the correct dust collection

General Information 3 1.1. Introduction 3 1.2. Manufacturer 3 2. Machine’s description and purpose of use 3 2.1. Machine’s description 3 2.2. Technical features 5 2.3. Cutting diagram 6 2.4. Overall dimensions 7 2.5. Part lists and technical drawings 8 3. Safety 10 3.1. Safety information 10 3.2. Accident prevention 10 3.3. General safety information 11 4. Transport of the machine 12 5. Installation of your machine 13 5.1. Preparation 13 5.2. Electric connection 14 6. Machine safety information

Don’t operate the machine with an air pressure lower than 6 Bar. 7.1. ADJUSTING THE AIR PRESSURE OF PNEUMATIC CLAMPS 7.1.1. Pull the adjustment button of the conditioner upwards. a-Turning the adjustment button in clockwise direction increases the pressure b-Turning the adjustment button in counter clockwise direction decreases the pressure c-Once you read 6-8 Bar (90-120 psi)on the manometer, push the adjustment button of the conditioner down and lock it in that position. 16 Operating and Safet

Not reading or observing of them may cause damage to the equipment or personal injury. IMPORTANT The IMPORTANT symbol above is one telling to apply special care and to be careful at carrying out the specified operation. CAUTION! The CAUTION! Symbol above warns you against specific dangers, and requires to read the text. Not observing may cause damage to the equipment. DANGER WARNING The above symbol DANGER WARNING, warns you against specific dangers, and you have definitely to read them. Neglige

The machine’s serial number and manufacturing year are stipulated on the technical label. 2. MACHINE’S DESCRIPTION AND PURPOSE OF USE 2.1. MACHINE’S DESCRIPTION Portable miter saw for serial cutting of PVC, aluminum and wooden profiles in desired angles. The operator has the possibility to adjust the cutting speed of the saw blade via knob according to material type and size. . Cutting at fixed angles of 150-22.50-300-450-900, and at intermediate angles via fixing arm. Machine has been designed

These precautions include: 1. Read all instructions before using the appliance. 2. To avoid fire or shock hazard, plug the appliance directly into a 120V AC electrical outlet. 3. If the filter is covered by a bag when shipped, remove plastic bag before use. 4. Keep the cord out of heavy traffic areas. To avoid fire hazard, NEVER put the cord under rugs, near heat registers, radiators, stoves, or heaters. 5. To protect against electrical hazards, DO NOT immerse the appliance in water or other liq

Volt 110V Frequency 60Hz H.P. 3.4 H.P. Amps 5.5 No load strokes 300-2000/min Max. cutting thickness wood 41.2" Stroke 13.16" Weight 71.4 lbs -4-H0799 Reciprocating Saw OPERATION Any time the saw is plugged into a power source, the reciprocating blade will activate when the trigger is depressed. Before making any adjustments or when changing blades, always remove the plug from the power source first. Failure to observe this will lead to serious personal injury. Inserting and Removing Saw Blades:

There is a possibility of fire hazard. Have the battery and charging unit checked by a qualified electrical service technician. G8598 51.8" Cordless Trim Saw -6 BEFORE YOU START, CONT’D Please take the time to familiarize yourself with the controls of your new saw. Below are listed the names of controls and features found on the saw and an explanation of their function. Please refer to Fig. 3, 4 & 5. Fig 3. Top view. From Figure 3: Blade Lock: Used to lock blade when installing or removing blade

10/08 and Later) -71- 5_ 7_ 8_ 9_ 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 -1', Motor and Arbor Parts List PART # DESCRIPTION P0605X137 STRAIN RELIEF PN02M HEX NUT M10-1.5 PW04M FLAT WASHER 10MM PLW06M LOCK WASHER 10MM P0605X113 SPECIAL MOTOR BOLT PK02M KEY 5 X 5 X 40 PSS03M SET SCREW M6-1 X 8 P0605X1013 MOTOR PULLEY P0605X1014 FLAT BELT 220-J12 P6005 B