• Never use your hands to remove sawdust, chips or waste close by the saw blade. • Use only blades as recommended. • Rags, cloths, cord, string and the like should never be left around the work area. • Avoid cutting nails. Inspect the workpiece and remove all nails and other foreign objects before beginning sawing. • Support the work properly. • Never reach over the blade to remove waste or off cuts. • Do not attempt to free a jammed blade before first switching off the machine. • Do not slow or

Upper blade guide assembly 17. Upper guide assembly lock knob 18. Dust extraction port (not shown) 19. Upper blade guide 20. Upper blade support head (not shown) 21. Lower blade support head (inside wheel housing) 22. Table 23. Lamp 24. Protractor 7 5 2 6 3 23 11 16 17 19 22 12 13 14 4 21 24 8 9 1 10 Setting up Electrical installation WARNING. The band saw is equipped with a 230 – 240V ~ single phase 200W motor. It must be connected to an earthed socket and it is recommended that a residual curr

4. Tighten the bevel adjustment knob (6) to secure the base plate. 8 Under bench use 1. Set the saw into the bench as required, ensuring the saw is secured adequately. 2. Attach a vacuum adapter to the saw. 3. Ensure the retracting blade guard can retract and return freely, operating as designed, before plugging cordset in the mains socket. 4. Run saw up to ensure it is running smoothly before attempting any cutting. 5. Make sure guarding is suitable so that the operator cannot touch the saw bla

5. Do not charge batteries for “top up”. Batteries should be placed on charge only when the battery is noticeably running down or the tool no longer performs a task it previously performed. 6. Unplug the adaptor charger and charging slide when not in use and store them in a dry, secure place. 7. Do not charge your battery pack in temperatures below 0°C or above 40°C. 8. Always remove the battery pack and store it in a dry, secure place when the tool is not in use. 9. Battery charging should only

• Always adjust the drop foot to just clear the workpiece to protect the operator, keep blade breakage to a minimum and provide maximum support for the blade. • Always adjust blade tension correctly. • The scroll saw should cut on the down stroke. Always make sure blade teeth are oriented downward towards the table. • When cutting a large piece of material make sure it is supported at table height. • Hold the work firmly against the table. • Do not feed the material too fast while cutting. Only

Disc guard 4. Front spark shield 5. Spark shield locking knob 6. Cut off disc 7. Spindle lock 8. Rear spark shield 9. Base 10. Rubber foot 11. Vice lock release lever 12. Vice handle 13. Vice 14. Fence 15. Carry handle 16. Lock down knob 17. Depth stop 18. 8mm Hex key 19. 5mm Hex key 1 18 19 3 16 2 15 4 5 7 6 17 8 14 13 9 11 16 12 10 Overview The cut off saw is used for cutting steel such as pipe, box section, rectangular, angle iron and steel bars. The saw can cut at angles from 0° to 45° left

16. Replace the guard retraction arm (6) and secure onto the rotating blade guard (5). 17. Check that the blade guard operates correctly and covers the blade as the saw arm is lowered. 18. Connect the saw to the power supply and run the blade to make certain that it is operating correctly. OperationCross cut A crosscut is made by cutting across the grain of the workpiece. A 90. crosscut is made with the mitre table set at 0.. Mitre crosscuts are made with the table set at some angle other than z

Power tools create sparks which may ignite the dust or fumes. • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. Electrical safety • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. • Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and re

• Always remove the plug from the mains socket before making any adjustments or maintenance, including changing the blade. WARNINGS. Before connecting a tool to a power source (mains switch power point receptacle, outlet, etc.) be sure that the voltage supply is the same as that specified on the nameplate of the tool. A power source with a voltage greater than that specified for the tool can result in serious injury to the user, as well as damage to the tool. If in doubt, do not plug in the tool