3. Please refer to the section titled Blade Changes on page 25 to install the blade. 4. Tension the blade enough to keep it on the saw so it does not spring off during the rest of the assembly process. 3. Place the large hex bolt with washer through the table trunnion mount and the trunnion. The assembly should now look similar to Figure 6. DO NOT connect power to the bandsaw until instructed to do so. Failure to do this may result in serious personal injury. Dust Port Guide Post To install the

Use the shims that came with the scoring blade set (Figure 38) to stack the scoring blade to the same thickness as the main blade. Figure 38. Typical scoring blade with shims. 5. Install the blade set with the teeth facing the opposite direction as the main blade, then reinstall the arbor flange and the arbor nut. 6. Place a hex wrench in the hole in the arbor and use the arbor wrench to tighten the arbor nut as shown in Figure 39. Note: The arbor nut has right-hand threads and tightens by turni

Turning off controls will not reduce this risk. ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3.Do not allow anything to cover or clog the charger vents. 4.Always cover the battery terminals with the battery cover when the battery cartridge is not used. 5. A battery short can cause a large current flo

YOUR FEEDBACK IS VITAL TOTHE SUCCESS OF DEWALT'S QUALITY IMPROVEMENT PROGRAM. See our catalog on the World Wide Web at INSTRUCTIVO DE OPERACION, CENTROS DE INSTRUCTION MANUAL SERVICIO Y POLIZA DE GARANTIA. ADVERTENCIA: GUIDE D'UTILISATION LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. SI TIENE DUDAS, POR FAVOR LLAME. MANUAL DE INSTRUCCIONES DW746, DW746X Woodworker’s Table Saw Scies circulaires a table d’entrepreneur Sierra de banco para madera Definitions: Safety Guidelines The definitions b

the duct covers conceal the ductwork running from the top of the hood to the ceiling or soffit. Before you begin, you should determine the installation height of the hood and order the correct size duct cover. Optional 6" or 12" ZX6DC30YSS–6" high decorative duct cover Duct Cover ZX12DC30YSS–12" high decorative duct cover Dimensions and Clearances: These vent hoods must be installed 30" min. and 36" max. above the cooking surface. Installation will be easier if the vent hood is installed before

/ 550 mm Art. Code: PC-22-FILE-U7 MEDIUM 16” 16. / 400 mm Art. Code: PC-16-FILE-U7 DOVETAIL 10” 10. / 250 mm WOOD AND PLASTIC. DOVETAIL RIGHT. Art. Code: PC-10-DTR DOVETAIL 10” 10. / 250 mm WOOD AND PLASTIC. DOVETAIL LEFT. Art. Code: PC-10-DTL DOVETAIL 10” 10. / 250 mm WOOD AND PLASTIC. DOVETAIL FLEX. Art. Code: PC-10-DTF PLASTER 24” 24. / 600 mm Art. Code: PC-24-PLS General purpose saw GENERAL PURPOSE 15” 15. / 380 mm Art. Code: PC-15-GNP Polystyrene, foam saw DECOR 16” 16. / 400 mm Art. Code:

Failure to do so can cause stalling and kickback. Any other conditions which could result in pinching, binding, twisting, or misalignment of the blade could cause kickback. Refer to the sections on “Adjustments and Set-Up” and “Operation” for procedures and techniques that will minimize the occurrence of kickback. TOOL LUBRICATION NOTE: With a new saw, change the oil after the first 10 hours of use and once per year after that. This action will greatly extend the life of your unit. 1. Always

6 and serrated flange nuts (D). PLACiNG SAW AND EXTENSioN TABLE oN MoBiLE BASE RiSK oF iNJURY FRoM LiFTiNG. Serious injury can result from attempting to lift too heavy an object. The machine can weigh more than 550 pounds and is too heavy to be lifted by one person. Obtain assistance from others before lifting. PiNCH HAZARD. Be sure not to place toes or fingers underneath the base of the Unisaw while moving. Lift the saw from underneath the table, before saw is assembled, or from underneath the

c-................................. amperes herts kilograms hours minutes seconds alternating current direct current no load speed alternating or direct current Class II Construction splash-proof construction watertight construction revolutions or reciprocation per minute number of blow IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE 1. SAVE THESE INSTRUCTIONS - This manual Length of Cord (Feet) 25 50 100 150 AWG Size of Cord 18 18 18 16 ADDITIONAL SAFETY RULES FOR CHARGER & BATTER