(4) Reset the filter to the fuel tank, and securely tighten the fuel tank cap. (5) Then, continue to operate the engine until it stops. (6) Remove the spark plug, and drip several drops of engine oil through the spark plug hole. (7) Gently pull the starter handle so that engine oil will spread over the engine, and attach the spark plug. (8) During storage, in order for the machine to become uprighting, please keep. (9) Keep the drained fuel in a special container in a well-ventilated shade. 16 F

Remedy Engine does not start Failure to operate primer pump Push 7 to 10 times. Low pulling speed of starter rope Pull strongly. Lack of fuel Feed fuel. Clogged fuel filter Clean Broken fuel tube Straighten fuel tube Deteriorated fuel Deteriorated fuel makes starting more difficult. Replace with new one. (Recommended replacement: 1 month) Excessive suction of fuel Set throttle lever from medium speed to high speed, and pull starter handle until engine starts. If engine will not start still, remo

(4) If oil adheres to the element (sponge), squeeze it firmly. (5) For heavy contamination: 1) Remove the element (sponge), immerse it in warm water or in water-diluted neutral detergent, and dry it completely. 2) Clean the element (felt) with gasoline, and dry it completely. (6) Before attaching the element, be sure to dry it completely. Insufficient drying of the element may lead to difficult startup. (7) Wipe out with waste cloth, oil adhering around the air cleaner cover and plate breather.

Inspection and Refill of Engine Oil (1) Perform the following procedure, with the engine cooled down. • Inspection: Please inspect whether it makes the machine horizontal, removes the oil cap, there is a oil to inside the range of the upper limit lower limit mark of gauge. When it is insufficient, (especially, when it has not reached to the lower limit level), please refill new oil. • Refill: Verticality (under the suction port cover) please do the machine, remove the oil cap. When oil is suppli

7 Assembly instructions .................................................................... 8 Before start of operation ......................................................... 9-10 Operation ................................................................................ 11-12 Adjustment of idling ...................................................................... 12 Operation method ......................................................................... 13 Inspection and maintenance ...

Conservez soigneusement ce manuel. Importante: Las bien este manual antes de poner el soplador en funcionamiento, y observe estrictamente las medidas de seguridad. Conserve este manual de instrucciones. INSTRUCTION MANUAL INSTRUCTIONS D’EMPLOI INSTRUCCIONES DE MANEJO English English Thank you very much for selecting the DOLMAR blower. We are pleased to be able to offer you the DOLMAR blower which is the result of a longdevelopment programme and many years of knowledge andexperience. The blower m

Cruise control lever OFF ON ADJUSTMENT OF IDLING DANGER The carburetor is the adjustment being completed at the time of factory shipment. Please do not adjust other than idling adjusting. When adjustment becomes necessary, please consult your dealership or an authorized service agent. Checkup of low-speed rotation Set the low-speed rotation to 3500 ( /min). • If it is necessary to change the rotation speed, regulate the adjusting screw, with Phillips screwdriver. • Turn the adjusting screw to th

(9) Rotation of the engine speed stabilizes and when from low speed making at high speed rotation, if reaches the point where it accelerates smoothly, it is completion of warming-up. (2) Stop Switch (6) Primer pump Close(3) (4) (7) Open 11 NOTE • The engine may be damaged if the choke lever is moved further beyond the “CLOSE” position. • If the engine stops with an explosion sound or if the engine started, but stopped before operation of the choke lever, return this lever to the “OPEN” position

Cylinder bottom gasket defective, crankshaft seals damaged, cylinder or piston rings defective or improper sealing of spark plug Broken starter spring, broken parts inside of the engine Carburetor contaminated, have it cleaned Incorrect idling adjustment, carburetor contaminated Fuel tank vent defective, fuel supply line interrupted, cable or STOP-switch faulty Air filter contaminated, carburetor contaminated, muffler clogged, exhaust duct in the cylinder clogged Operating time Item Before opera

• As an example to keep the oil gauge clean, it is recommended to insert the oil gauge on its knob side into the engine cover. Point 1 in Replacement of Oil “Oil Gauge” Shelf Shelf • It becomes cause of the oil soiling. Be sure to wipe out spilt oil before start of operation. Point 2 in Replacement of Oil: “If oil spills out” 9 2. Fuel supply WARNING • • When supplying the fuel, be sure to observe the following instructions to prevent ignition or fire: - Fuel supply must be made in a place free