Assessments - 3, GPA: 4 ( )

Fabricante : Electrolux Arquivo Tamanho: 894.87 kb Arquivo Nome : Língua de Ensino:

phase 2 flashing 1 2 selected item P : M EN U 6) Set new values, as described in point 2), but this time with reference to phase 2. 7) To set additional phases repeat steps 4, 5 and 6 up to a maximum of 7 phases. 8) The multiple phase cooking program has now been set up. Place the product to be cooked in the oven and press the Start cycle button. The cooking cycle will start from phase 1 (value 1 flashes in alternation with a dot on the relative DISPLAY) and, when phase 1 is terminated, it will advance automatically to phase 2 (value 2 flashes in alternation with a dot on the relative DISPLAY) and so on until all set phases are completed. phase 2 in progess 1 2 The transition from one phase to the next is signalled by a short audible signal. When the last phase is terminated the cooking cycle will stop automatically as already described, and the appliance will emit a double intermittent audible signal. To repeat the same multiple phase cycle simply press the START/STOP button again. While the cooking cycle is in progress you can skip one or more of the phases as follows: - press the (>) button one or more times to select the successive phases. - press button P once and then press it again at the "SKIP PHASE" option to confirm the selected phase and cause it to start. 4.4 AUTOMATIC CONTROLS Introduction: the automatic controls make it possible to perform cooking cycles in special modes and also to store cycles after manual setting. For information on manual setting procedures refer first to heading 4.3 MANUAL CONTROLS. Note: If the oven is switched off after you have set up a cooking cycle manually the data you have entered will be lost since, in manual mode, the controller does not store the cooking cycle. To store manually set cooking programs for future use proceed as described in the following headings. The cooking cycles (or RECIPES) and programs (e.g. CLEAN) are managed by means of the following commands: Recipes or programs ---------- DISPLAY Menu* ---------------- ^ < > v * list of commands (items) necessary for executing the various management functions: S 00 M E N U S 06 A D D P H A S E S 03 S K I P P H A S E S 07 A D D D E L A Y S 09 C L E A R P H A S E S 17 C O N F I R M S 18 R E T U R N S 10 C L E A R R E C I P E S 17 C O N F I R M S 18 R E T U R N S 11 M E M O R I Z E R E C I P E S 13 S E L E C T N U M B E R S 02 C O N F I R M S 14 E D I T N A M E S 02 C O N F I R M S 15 S A V E R E C I P E S 16 R E T U R N S 04 S E A R C H B Y N A M E S 01 C O N F I R M S 05 S E A R C H B Y N U M B E R S 12 E X I T S 17 C O N F I R M S 18 R E T U R N S 19 P A S S W O R D S 20 N E W P A S S W O R D S 21 C O N F I R M P A S S W O R D S 22 C H A N G E P A S S W O R D P (Program) = button to: - open the list of recipes and programs - open the menu of recipes or programs - confirm the items selected from the menus (^) (v) = "arrow" buttons (up and down) (or use the knob) to: - select recipes, programs or relative names - select menu items - select the utilities - set the values (<) (>) = "arrow" buttons (left and right) to: - return to menu - select the phases DISPLAY = displays the operations described above 24 USA 5938 035 4) Set the required START time (shown in small numbers on the TM timer display) and press the START/STOP button. The cycle will start at the time set in the DELAY START option and the letter D will flash in alternation with a dot to remind the user that this function is active. 4.4.3 EDI...

Baixe o seu

Para fazer o download, introduza 2 dígitos :