Ensure that the leveling leg is positioned over the 2 x 4 before leveling the insert. September 1, 2008 7036-135E Page 11 Mt. Vernon Pellet Insert (AE) 4 44V VVent Information ent Informationent Information A. Venting Termination Minimum Requirements R J or XV M I HA V G B V V A B V F V C B B E L V D V Electrical Ser ice V NV N V N N V Inside orner FIXED CLOSEDOPEN OPEN FIXED CLOSED V X G GTermination Cap Air Supply Inlet Gas Meter Restricted Area O P Figure 12.1 All minimum clearances are liste

• Failure to do so could result in smoking, sooting and possible hopper fires. E. Baffle Removal Baffle Latches Insert flat head screw driver into “V” section and push down and the bottom of the latch will fall forward off of post Locating ears - 1 on each side. Fit behind bottom edge. Figure 36.2 WARNING Cast iron is a very heavy material. The baffle is made of cast iron and therefore is heavy and awkward at times to maneuver. Clear and prepare your work area before you begin. a. The appliance

Figure 24.4. 3. Automatic or Manual Setting The automatic setting will control the heat output based on the comfort level selection. The manual setting allows you to manually control the heat output settings. See Ignition Cycles on page 25. NOTE: See the Wall Control Thermostat manual for detailed instructions. FUEL SELECTION Corn Utility PelletSoftwood Pellet Sunflower Seeds Wheat Hardwood Pellet DONE SELECT Figure 24.3 Figure 24.4 Page 24 7036-135E September 1, 2008 R R Mt. Vernon Pellet Inser

29 Auto-Clean Cam, Switch SRV7034-187 30 Switch, Micro, Normally Open 7000-327 31 Motor 12 Volt 7000-300 32 Auto-Clean Motor Grommet 7034-188 Item Description Part Number 1 Door Frame Assembly 7034-026 2 Latch Assembly, Door 7034-039 3 Glass Assembly 7034-007 4 Glass Retainer 7034-136 5 Hinge, Female 450-2910 6 Magnet & Bracket Assembly 7034-008 7 Door Air Deflector 7034-185 Page 42 7036-135E September 1, 2008 R Mt. Vernon Pellet Insert (AE) Figure 42.1 # Description # Description # Description

(51 mm) Minimum Height Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm) Place waterproof sealer under each flange of the termination cap and on top of each screw to help prevent leaks. The last section of pipe must stop between 2 in. (51 mm) above top of chase and 7 in. (178 mm) below top of chase 2 in. (51 mm) 7 in. (178 mm) Figure 9.8 Installing a TCT375 Terra Cotta Cap • TCT375 Terra Cotta Cap 110 Shrouds A. Radiation Shield • Some shrouds require a radiation shield. Us

PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS BIOMASS CORN/ WOOD PELLET BURNING STOVE. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH. IMPORTANT: Always contact your local dealer/installer with questions before contacting the factory. When you call have your serial number, purchase date, who installed the unit and a list of questions. This appliance must be installed by a qualified/trained factory approved installer to assure

Do not cut corners. Serious complications and possible safety risks may occur. Always use a certified installer. This installation is not recommended FIREPLACE INSERT INSTALLATION CONTINUED…… The MagnuM Countryside Model 3502 Fireplace Insert requires a fireplace shroud for proper installation. The shroud is designed to slip over the stove-top between the front and back hopper lids. Shrouds can be customized for particular installations (custom order). 1) Position unit so that the shroud can be

WARNING • Do NOT store flammable materials in the appliance’s vicinity. • Do NOT use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or “freshen up” a fire in this heater. • Keep all such liquids well away from the heater while it is in use. • Combustible materials may ignite. Fire Risk. WARNING • High ash fuels, or lack of maintenance, can cause the firepot to fill with ash and clinker. If the firepot fills to the top, immediately shut down the unit and clea

Combustible materials may ignite. September 1, 2008 7039-131F Page 25 2100 Millennium Wood Stove (ACC) R K. Frequently Asked Questions ISSUES SOLUTIONS Odor from appliance When first operated, this appliance may release an odor for the first several hours. This is caused by the curing of the paint and the burning off of any oils remaining from manufacturing. Metallic noise Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the sound produced by a furnace

Warranty starts with date of purchase by the original owner (end User) except as noted for replacement parts. Warranty Period HHT Manufactured Appliances and Venting Components CoveredParts Labor gas WoodPellet ePA Woodelectric Venting1 Year XXXXXXAll Parts and Material except as covered by Conditions, exclusion, and Limitations listed2yearsXXIgniters, electronic Compo- nents, and glass XXXXblowers XMolded refractory Panels 3yearsXFirepots 5years3yearsXXCastings & baffles 7years3yearsXXXFirebox,