Use copper wire only. A time-delay fuse or circuit breaker and separate circuit is recommended. Water: A hot water line with 20-120 psi (138-862 kPa) water pressure. Water temperature must be minimum 120°F (49°C) at dishwasher. Use 3/8" O.D. copper tubing with compression fitting or flexible stainless steel braided fill line (1/2" minimum plastic tubing is not recommended). Use a 90° elbow with 3/8" N.P.T. external pipe threads on one end to connect to water inlet valve. Do not solder within 6

Turn off electricity to the dishwasher. The Winter Season: To protect against possible rupture of fill valve, BE SURE water lines leading to, as well as in the dishwasher, are well protected against freezing. RUPTURES OF THIS KIND ARE NOT COVERED BY THE WARRANTY. To safeguard your KitchenAid dishwasher when it is exposed to freezing temperatures in a seasonal dwelling, have a local qualified person do the following: 1. Close and latch the door. 2. Turn off electricity to the dishwasher. 3.

The float must be in place for the dishwasher to operate. Important: A small amount of water always remains in the bottom of the dishwasher (under the ultrafine filter) to keep the seal moist. The coarse strainer may be removed, if necessary. To remove, lift strainer out by squeezing center section (F) and remove. To replace, squeeze center section so clips snap into square notch. Possible Burn Hazard Heating element will be hot immediately following use. Do not touch. To avoid burns wait at

34 Drain Function 1. During the Drain function, a separate drain pump motor (1) is started while the main wash pump motor continues to operate for 1 minute. This accomplishes three goals. 2. First, the jets on the underside of the lower spray arm continue to flush soils from the accumulator screen while the water is drained from the unit. (2) 3. Second, negative pressure in the main wash pump inlet chamber keeps the check valve closed, allowing the drain pump to remove soiled water from the accu

OBSERVE ALL LISTED WARNINGS AND CAUTIONS. For Replacement Installation -Review these complete instructions to be sure that previous connections are compatible. For New Installations -Plumbrng and electrical connections must be provided before the dishwasher is moved Into place. These instructions are intended for use by qualified workers who will observe all local codes and ordinances for plumbing connections as well as local codes and/or the Canadian Electrical Code for’electrical connections.

Sanitized If you select the SANI RINSE™ option, the Sanitized indicator glows when the SANI RINSE™ cycle is finished. If your dishwasher did not properly sanitize your dishes, the light flashes at the end of the cycle. This can happen if the cycle is interrupted or the incoming water temperature is too low. The light goes off when you open and close the lid. Check Drain If the dishwasher senses the drain stopper is not closed properly, the cycle immediately ends, the lid pops open, and the Check

The dishwasher resumes the new cycle and/or option after a 5-second pause. After the first fill of a cycle 1. Open the lid. 2. Press the Cancel pad. 3. Close the lid. Your dishwasher starts a drain. Let the dishwasher drain completely. 4. Open the lid. 5. Select a new cycle and/or options. 6. Check the detergent. Dishwasher must contain the proper amount for the new cycle. 7. Press the Start pad. 8. Close and latch the lid. AddingItemsDuringaCycle You can add an item anytime before the main wash

After checking “Troubleshooting,” additional help can be found by checking the “Assistance or Service” section or by calling KitchenAid. In the U.S.A., call 1-800-422-1230. In Canada, call 1-800-807-6777. 9/05 Keep this book and your sales slip together for future reference. You must provide proof of purchase or installation date for in-warranty service. Write down the following information about your major appliance to better help you obtain assistance or service if you ever need it. You will n