Hopper Strap 9. Hopper Assembly Hardware Package (see page 3) 567149238 EFDCBAKLMGHIJNOQRSNOT SHOWN FULL SIZESHOWN FULL SIZEP REF. QTY. DESCRIPTION A 6 Hex Bolt, 1/4-20 x 2" B 2 Hex Bolts, 3/8-16 x 1-1/4" C 4 Hex Bolt, 1/4-20 x 1" D 1 Carriage Bolt, 1/4-20 x 3/4" E 10 Nylock Nuts, 1/4" F 2 Nylock Nuts, 3/8" G 6 Nylon Washer H 10 Flat Washer, 5/16" I 4 Flat Washers 1-5/8" J 1 Cotter Pin, 3/32" x 3/4" K 1 Cotter Pin, 1/8 x 1-1/2" L 1 Hair Cotter Pin, 1/8" M 1 Hitch Pin N 1 Short Spacer Tube O 1 Lo

The rate chart is calculated for light and heavy application. The faster you drive, the wider the broadcast width. A variation in speed will determine the flow rates and width of broadcast. CAUTION When broadcasting weed control fertilizers make sure broadcast pattern does not hit evergreen trees, flowers or shrubs. FIGURE 16 SPROCKET SHAFT AGITATOR WIRE 3/8" LOCKNUT AGITATOR SLEEVE FIGURE 17 5. Keep tires inflated to 15-20 P.S.I. Do not over inflate. FIGURE 18 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

DESCRIPTION KEY QTY. DESCRIPTION A B C D E F G H I 6 2 2 1 8 2 2 4 8 Hex Bolt, 1/4-20 x 1-3/4" Hex Bolts, 3/8-16 x 1-1/4" Hex Bolt, 1/4-20 x 3/4" Carriage Bolt, 1/4-20 x 3/4" Hex Lock Nuts, 1/4-20 Thread Hex Lock Nuts, 3/8-16 Thread Lock Washers, 3/8" I.D Nylon Washer Flat Washer, 5/16" J K L M N O P Q R S 4 1 1 1 1 2 1 1 1 1 Flat Washers 1-5/8" Cotter Pin, 3/32" x 3/4" Cotter Pin, 1/8 x 1-1/2" Hair Cotter Pin, 1/8" Hitch Pin Spacers Nylon Wing Nut Adjustable Stop Flow Control Link Grip 3 5.Alig

3. Remove the lock nut from the middle bolt in the crossover tube and shaft support plate. Leave the bolt in place. See figure 2. 4. Assemble the short end of the hitch tube onto the middle bolt and secure it with the same nut you removed. DO NOT TIGHTEN YET. See figure 2. IMPORTANT: The hitch tube must attach to the side of the crossover tube opposite the shaft support plate. 5. Assemble the two hitch braces to the hitch tube using a 1/4" x 2" hex bolt and a 1/4" nylock nut. DO NOT TIGHTEN YET.

44483 (Rev. 4/90) RULES FOR SAFE OPERATIONS The following safety precautions are suggested. This broadcast spreader is designed, engineered and tested to offer reasonably safe and effective service, provided it is operated in strict accordance with these instructions. Failure to do so may result in personal injury. Always observe the rules of safe operation. 1. Do not allow anyone to operate the broadcast spreader without proper instructions. 2. Do not permit children to operate the broadcas

(Refer to figure 2 on page 4.) Use shim washers (Ref. no. 20 on pages 10 and 11) as needed for minimum backlash. Add grease to gear and sprocket. 2. If the agitator wire becomes damaged or worn it can be replaced. Loosen the 3/8" hex nut on top of the sprocket shaft until agitator wire is free. Remove old agitator wire from hole in agitator sleeve and replace with new agitator wire. Position agitator wire so that sprocket shaft turns freely, then tighten 3/8" hex nut on top of sprocket shaft. Se

Tighten 1/4" lock nuts. FIGURE 11 5/16" FLAT WASHER NYLON WASHER 1/4" x 3/4" CARRIAGE BOLT NYLON WING NUT ADJUSTABLE STOP OFF ON 1234 678910 5 FLOW CONTROL ARM ON OFF AJDUSTABLE STOP SETTING "5" FIGURE 12 7 24. Attach an angle stop bracket and a swivel bracket to the rear hole in the R.H. shield bracket using a 1/4" x 3/4" hex bolt, two 5/16" washers, a nylon washer and a 1/4" hex lock nut. Place the angle stop bracket on the inside and the swivel bracket on the outside. Tighten the locknut so t

45-02103 125 LB. PUSH BROADCAST SPREADER CAUTION: Read Rules for Safe Operation and Instructions Carefully Assembly Operation Maintenance Repair Parts the fastest way to purchase parts PRINTED IN U.S.A. FORM NO. 49030 (REV. 4/7/08) 2 RULES FOR SAFE OPERATION The following safety precautions are suggested. This broadcast spreader is designed, engineered and tested to offer reasonably safe and effective service, provided it is operated in strict accordance with these instructions. Failure to do so

See figure 2. AXLE SPACER 5/8" FLAT WASHER 5/8" FLAT WASHER HUB CAP WHEEL NO CROSS HOLE HUB CAP 5/32" x 2" COTTER PIN CROSS HOLE 5/8" FLAT WASHER 8. Remove the nut from the middle bolt in the crossover tube. See figure 4. CROSSOVER TUBE MIDDLE NUT SHAFT SUPPORT MIDDLE BOLT PLATE 5 FIGURE 7 13. Assemble the leg stand tube to the handle tube (long) using two 1/4" x 1-1/2" hex bolts. Secure tightly with two 1/4" nylock nuts. See figure 6. 14. Place a vinyl cap over the end of the leg stand tube. Se

The approximate broadcast widths for different materials are shown in the application chart on this page. 10. When broadcasting weed control fertilizers, make sure the broadcast pattern does not hit evergreen trees, flowers or shrubs. 11. Heavy moisture conditions may require a cover over the hopper to keep contents dry. The vinyl cover (available as an accessory) acts as a wind and moisture shield, but should not be used as a rain cover. Refer to the parts list on page 11. IMPORTANT: Applicatio