45-0414 45-0415 125 LB. TOW BROADCAST SPREADER • Safety • Assembly • Operation • Maintenance • Parts CAUTION: Read Rules for Safe Operation and Instructions Carefully the fastest way to purchase parts FORM NO. 40454 Rev. (5/15/09) PRINTED IN USA 2 RULES FOR SAFE OPERATION Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when operating equipment. • Read the towing vehicle owners manual and to

1. Turn the spreader upside down as shown in figure 1. FIGURE 2 6. Tighten the nuts and bolts fastening the hitch braces to the hopper frame and the hitch tube, then tighten the middle lock nut fastening the hitch tube to the crossover tube. DO NOT COLLAPSE TUBES WHEN TIGHTENING. 7. Assemble a spacer (P), a 3/4" flat washer (K), a wheel (air valve facing out) and another 3/4" flat washer (K) onto the end of the axle that has only the small hole. See figure 3. 8. Install a 1/8" x 1-1/2" cotter pi

Stay off steep slopes! • Follow maintenance and lubrication instructions as outlined in this manual. LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS — ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. ENGLISH ASSEMBLY INSTRUCTIONS 4. Assemble the four hitch braces in pairs to the inside of the hopper frame using a 1/4" x 1-3/4" hex bolt (B) and 1/4" nylock hex nut (F) on each side. DO NOT TIGHTEN YET. See figure 2. 5. Assemble the two OUTER hitch braces to the hitch tube

This unit will cover a 4 to 8 foot wide area depending on the material used and the towing speed. 2. To avoid misses or striping, make each pass about 5 feet from the previous one so some overlapping of spread pattern does occur. 3. For easiest application, spread across the shortest edges of lawn first, making two "header" strips for a turning area, and then spreading between the header strips. See figure 6. 4. If lawn is odd shaped, spread a border around the edges and then spread between the

Assemble the Hitch Brackets to the Hitch Control Tube using two 1/4" x 1-3/4" hex bolts and 1/4" hex nuts. Tighten. See figure 3. 5. Assemble the hitch pin through the hitch brackets and secure with the 1/8" hair cotter pin. See figure 3. 6. Assemble the vinyl cap onto the Hitch Control Tube. See figure 4. 7. Assemble the Control Cable to the Hitch Control Tube using the 1/4" x 2-1/4" carriage bolt and nylon wing nut. See figure 4. FIGURE 4 FIGURE 3 ASSEMBLY INSTRUCTIONS 1/4" x 2-1/4" HEX BOLT 1

See figure 10. 1/4" x 5/8" HEX BOLT1/4" HEX LOCK NUT FLOW CONTROL LINK EXTENSION SPRING FLOW CONTROL ROD FLOW CONTROL MOUNTING BRACKET FLOW CONTROL ARM FIGURE 10 19. Place a 5/16" flat washer over the end of flow control rod, and insert end of rod through slot in flow control mount bracket and through the hole in flow control link. Secure with a 3/32" x 3/4" cotter pin. See figure 11. FLOW CONTROL LINK EXTENSION SPRING 3/32" COTTER PIN 5/16" FLAT WASHER FLOW CONTROL ROD FLOW CONTROL MOUNTING BRA

Hopper Strap 9. Hopper Assembly Hardware Package (see page 3) 567149238 EFDCBAKLMGHIJNOQRSNOT SHOWN FULL SIZESHOWN FULL SIZEP REF. QTY. DESCRIPTION A 6 Hex Bolt, 1/4-20 x 2" B 2 Hex Bolts, 3/8-16 x 1-1/4" C 4 Hex Bolt, 1/4-20 x 1" D 1 Carriage Bolt, 1/4-20 x 3/4" E 10 Nylock Nuts, 1/4" F 2 Nylock Nuts, 3/8" G 6 Nylon Washer H 10 Flat Washer, 5/16" I 4 Flat Washers 1-5/8" J 1 Cotter Pin, 3/32" x 3/4" K 1 Cotter Pin, 1/8 x 1-1/2" L 1 Hair Cotter Pin, 1/8" M 1 Hitch Pin N 1 Short Spacer Tube O 1 Lo

45-02142 CAUTION: Read Rules for Safe Operation and Instructions Carefully 100 LB. PUSH BROADCAST SPREADER Assembly Operation Maintenance Repair Parts thefastestway topurchaseparts PRINTED IN U.S.A. FORM NO. 48319 (REV. 11/03) RULES FOR SAFE OPERATION The following safety precautions are suggested. This broadcast spreader is designed, engineered and tested to offer reasonably safe and effective service, provided it is operated in strict accordance with these instructions. Failure to do so may re

Assemble the Hitch Brackets to the Hitch Control Tube using two 1/4" x 1-1/4" hex bolts and 1/4" nuts. Tighten. See figure 3. 5. Assemble the hitch pin through the hitch brackets and secure with the 1/8" hair cotter pin. See figure 3. TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" Wrenches REMOVAL OF PARTS FROM CARTON Remove all parts and hardware packages from the carton. Lay out all parts and hardware and identify using the illustrations on page 3. 1/4" NUT1/4" x 1-1/4" HEX BOLTHAIR COTTER PINHITCH PIN

The rate chart is calculated for light and heavy application. The faster you drive, the wider the broadcast width. A variation in speed will determine the flow rates and width of broadcast. CAUTION When broadcasting weed control fertilizers make sure broadcast pattern does not hit evergreen trees, flowers or shrubs. FIGURE 16 SPROCKET SHAFT AGITATOR WIRE 3/8" LOCKNUT AGITATOR SLEEVE FIGURE 17 5. Keep tires inflated to 15-20 P.S.I. Do not over inflate. FIGURE 18 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx