Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
2. Fasten the console to the console mounting plate with the four M5x12mm screws and washers using a Philips screwdriver. Handrail Assembly 1. Place the handrail supports into their receptors on the stabilizer bar. Insert and finger tighten eight M8x12mm bolts, from handrail assembly hardware bag, 4 on each side, to secure these supports. 2. Assemble upper handrails into handrail supports. Insert and finger tighten eight M8x12mm bolts, from handrail assembly hardware bag, 4 on each side, to secure these handrails. 3. Place handrail clamp cover onto handrails. Assemble the handrail clamp cover and handrails onto the upper portion of the console mast. Insert and finger tighten two M8x55mm bolts. 4. Tighten all 18 bolts of handrail assembly with an Allen wrench. Waterbottle 1. Place the bottle holder on the console mast. Insert and tighten the two M5x12mm screws using a Phillips screwdriver. 2. Snap the water bottle into the holder. Leveling Pad 1. Adjust both leveling pads, located on the bottom of stabilizer bar, to ensure your equipment is leveled with floor. 9 1 1 5 0 S E R I E S O W N E R’S M A N U A L 10 1 1 5 0 S E R I E S O W N E R’S M A N U A L 1150Er Assembly Drawing 1150Er Assembly Instructions 1150Er Assembly Instructions Console Mast Assembly 1. Lay the console mast down in front of the frame. 2. Connect main wire harness at the bottom of console mast to wire harness at the front of frame. 3. Slide console mast into console mast receptor at front end of frame. Be careful not to pinch the wire harness. 4. First, attach console mast to frame at lower hole-locations on both sides using two M10x20mm screws with their washers and an Allen wrench. NOTE: there are three holes on either side to choose from. The middle hole is for average-sized users and will be suitable for most. The hole closest to the footpads is for taller users, and the hole farthest from the footpads is for shorter users. Do not tighten yet. Tilt the mast into position. 5. Next, attach console mast at lower hole-locations on both sides of console mast receptor. Then tighten all screws in holes of console mast receptor. NOTE: In order to avoid console mast loosen up after a while of use. Please check and tighten these screws as often as possible. 5. Place console mast cover in the front of console mast. Insert and tighten four M5x12mm screws with a Phillips screwdriver. Handrail Assembly 1. Attach right handrail to the console mast at the right handrail axle using the set-screw collar. Tighten the set-screw of the right handrail set screw collar by using an Allen wrench. 2. Next, attach the right handrail to the bottom of the right steparm. Insert the handrail/steparm axle through the holes in the steparm and through the tube at the bottom of handrail. Insert a M8x20mmscrew with washer into steparm axle and tighten it using an Allen wrench and an open-end wrench on each side. 3. Assemble left handrail the same way. 4. Attach both steparm/handrail covers using M5x25mm screws each and a Phillips screwdriver. 5. On either side of water bottle cover, attach the handrail covers to each other around the handrails. Then use the two M4x 40mm screws and nuts on each side and tighten them with a Phillips screwdriver. Handlebar Assembly 1. Insert the hand pulse harness through the opening of the console mast and out of the console mounting plate. 2. Assemble the handlebar onto the mount and insert and tighten the four M8x12mm screws using an Allen wrench. Be sure not to pinch the hand pulse harness during this procedure, as this will damage the electronic console. Console Assembly 1. Connect both plugs, from main wire harness and hand pulse harness, to the plug receptors on the backside of the console, taking care to install correctly (see plug alignment marks). WIRING HARNESS INSTALLATION HINT: Any excess wiring must be carefully inserted (“stored”) back into the console mast before installing the console onto the console mounting plate. 2. Fasten the console to the console mounting plate with the four M5 x 12mm screws and washers using a Philips screwdriver. Transportation Wheel Assembly 1. Insert both Transportation wheel’s sleeves into stabilizer bar, making sure the screw hole is lining up with the hole of the stabilizer bar. Tighten both inner bushings with its screw using a Philips screwdriver. 2. Assemble Transportation wheels onto wheel sleeves until the clips are engaged. See assemby drawings for details. Waterbottle 1. Insert the water bottle into the water bottle holder. Leveling Pad 1. Adjust all leveling pads, located on the front-bottom of the main frame, to ensure your equipment is leveled with floor. 11 1 1 5 0 S E R I E S O W N E R’S M A N U A L 1150 Series Operation & Comfort Tips 1150 Series Operation & Comfort Tips General 1150 Series Tips 12 Cadence: There is a strong relationship between cadence (revolutions
Formadores - 1150Er (2.44 mb)
Formadores - 1150Rb (2.44 mb)
Formadores - 1150St (2.44 mb)
Formadores - 1150Ub (2.44 mb)