Assessments - 2, GPA: 3.5 ( )

Fabricante : GE Arquivo Tamanho: 2.32 mb Arquivo Nome : Língua de Ensino:

. Lights next to the touch pads on the air conditioner control panel indicate the selected settings. Consumer Support Troubleshooting TipsInstallationInstructionsCare and CleaningOperatingInstructionsSafety Instructions Light indicates the unit The display always shows the room is in the temperature or temperature except when setting the delay time Set mode. Set temperature or the Delay timer. Light indicates the delay timer is set. Light indicatesCirculaire is on. Air Conditioner Controls Controls The air conditioner controls are located behind the control panel door. Press to open and close the door. NOTE: The remote control will work with the control panel door open or closed. Power Pad Turns air conditioner on and off. When turned on, the display will show the room temperature. Display Shows the room temperature or time remaining on the Delay timer. Shows the Set temperature while setting the temperature in Cool or Energy Saver modes. The Set light will turn on while setting. NOTE: The display will change to show the room temperature after settings have been made. To recall the Set temperature, press the Temp Increase ^ or Decrease Ў pads. Temp Increase ^ /Decrease Ў Pads Use to set temperature when in Cool or Energy Saver mode. The Set light will turn on while setting. Delay Timer Increase ^ (+) /Decrease Ў (–) Pads Each touch of the Increase ^ / Decrease Ў pads on the unit or the Increase + / Decrease – pads on the remote control will set the delay time when using the Delay 1–24hr timer ( ). The Set light will turn on while setting. Fan Speed Pads Use to set the fan speed to Low, Med, High or Auto on the unit. NOTE: On the remote control, use the fan speed Increase + / Decrease – pads to set the fan speeds to Low, Med or High. Use the Auto pad to turn Auto fan on. Delay 1–24hr Delay timer Increase Delay timer Circulaire Decrease Mode select Auto Fan on/off Fan speed Mode Auto Power Temp Fan-Fan+ Delay Fan Remote Control Fan speed Increase Decrease Temperature Unit power on/off set Increase and Decrease Mode Pad Use to set the air conditioner to Cool, Energy Saver or Fan Only mode. Delay Pads Delay ON—When the air conditioner is off, it can be set to automatically come on in 1 to 24 hours at its previous mode and fan settings. Delay OFF—When the air conditioner is on, it can be set to automatically turn off in 1 to 24 hours. How to set: Press the Delay 1–24hr pad on the unit or the pad on the remote control. Each touch of the Increase ^ / Decrease Ў pads on the unit or the Increase + / Decrease – pads on the remote control will set the timer in 1-hour intervals. The Set light will turn on while setting. To review the remaining time on the Delay 1–24hr timer, press the Delay 1–24hr pad on the unit or the pad on the remote control. Use the Increase ^ / Decrease Ў pads on the unit or the Increase + / Decrease – pads on the remote control to set a new time if desired. To cancel the timer, press the Delay 1–24hr pad until the light on the Delay 1–24hr pad goes off. CIRCULAIRE Pad Turn on to provide continuous side-to-side air circulation. For fixed side-to-side air direction, turn on until the desired air direction is obtained, then turn it off. 4 ge.com Do Not Operate in Freezing Outdoor Conditions This cool-only air conditioner was not designed for freezing outdoor conditions. It must not be used in freezing outdoor conditions. Consumer SupportTroubleshooting and Instructions Cool Mode Use the Cool mode at Low, Med, High or Auto Fan Speed for cooling. Use the Temperature Increase ^ / Decrease Ў pads to set the desired temperature between 64°F and 86°F in 1°F increments. An electronic thermostat is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the set level of comfort. Set the thermostat at a lower number and the indoor air will become cooler. Set the thermostat at a higher number and the indoor air will become warmer. NOTE: If the air conditioner is off and is then turned on while set to a Cool setting or if turned from a fan setting to a Cool setting, it may take approximately 3 minutes for the compressor to start and cooling to begin. Cooling Descriptions For Normal Cooling—Select the Cool mode and High or Med fan with a middle set temperature. For Maximum Cooling—Select the Cool mode and High fan with a lower set temperature. For Quieter & Nighttime Cooling—Select the Cool mode and Low fan with a middle set temperature. Energy Saver Mode Controls the fan. ON—The fan will cycle on and off with the compressor. This results in wider variations of room temperature and humidity. Normally used when the room is unoccupied. NOTE: The fan may continue to run for a short time after the compressor cycles off. OFF—The fan runs all the time, while the compressor cycles on and off. Fan Only Mode Use the Fan Only Mode at Low, Med or High fan speed to provide air circulation and filtering without cooling. Since fan only settings do not provide cooling,...

Baixe o seu

Para fazer o download, introduza 2 dígitos :