Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
You will need to modify them for other types of windows. • The air conditioner can be installed without the accordion panels if needed to fit in a narrow window. See the window opening dimensions. • All supporting parts must be secured to firm wood, masonry or metal. • The electrical outlet must be within reach of the power cord. 1 18. min. 30. to 41. (With accordion panels) REMOVE THE AIR CONDITIONER FROM THE CASE Remove the locking screw and locking bracket from the lower frame. Save to reinstall later. Remove the ground screw and save to reinstall later. Slide the air conditioner from the case by gripping the base pan handle and pulling forward while bracing the case. A C B 4 Remove the ground screw and save to reinstall later STORM WINDOW REQUIREMENTS A storm window frame will not allow the air conditioner to tilt toward the outside, and will keep it from draining properly. To adjust for this, attach a piece of wood to the stool. WOOD PIECES WIDTH: 2. LENGTH: Long enough to fit inside the window frame. THICKNESS: To determine the thickness, place a piece of wood on the sill to make it 1/2. higher than the top of the storm window frame or the vinyl frame. Attach securely with nails or screws provided by the installer. 2 1/2. higher than storm window frame Storm window frame Wood Sill 1/2. higher than vinyl frame (on some windows) Vinyl frame 11 ATTACH THE TOP MOUNTING RAIL SEAL STRIP Remove the backing from the top mounting rail seal strip and attach the seal strip to the bottom of the top mounting rail, along the front edge. 3 Top mounting rail Remove backing from seal strip Top mounting rail Seal strip FRONT VIEW Window Installation Instructions 5 PREPARE THE WINDOW Cut the window sash seal to the proper length. Peel off the backing and attach the seal to the underside of the window sash. 7 A INSTALL THE CASE IN THE WINDOW Carefully slide the case into the window and center the case. Lower the window behind the top mounting rail. Pull the bottom of the case forward so that the bottom mounting rail is tight against the back of the window sill. Mount the case to the window sill using 4 type E screws. Drill pilot holes, if necessary. 4 type E screws 6 PREPARE THE CASE Sill Install the top mounting rail with 4 type B A screws from the inside of the case. Top mounting rail Insert the frames for the accordion panels B into the top mounting rail and the bottom frame guides. Attach the accordion panels to the side of the case using 3 type A screws on each side. Note: When attaching the accordion panels, make sure to only screw the inner panels to the case sides. Top mounting rail Make sure the bolts and nuts are all of the B way in both the left and right V-supports. Bolt and nut Position the V-supports on the case bottom C so that they will be near the outside wall. Attach a V-support to each side of the bottom of the case using type C screws, 3 on each side. V-support Type A BACK screws Bottom mounting rail 12 Window Installation Instructions INSTALL THE CASE IN THE WINDOW (cont.) Use a wood block (obtained locally) between the leveling bolts and the wall if the wall is weak or if the weight of the air conditioner falls between the studs in the wall. Adjust the leveling bolts and nuts against the outside wall so that the case has a slight tilt to the outside. Tighten nuts with an adjustable wrench. Use a level; no more than a 1/2 bubble will be the correct case slant to the outside. Extend the left and right accordion panels to the vertical window sashes. Drill pilot holes and attach the top and bottom corners with 4 type D screws. D F E 7 Type D screw Type D screw Type D screw Top mounting rail Type D screw INSTALL SUPPORT BRACKETS AND FOAM TOP WINDOW GASKET Drill pilot holes and attach the support brackets with two type D screws, one on each side. Cut the foam top window gasket to the window width. Stuff the foam between the glass and the window to prevent air and insects from getting into the room. NOTE: If the gasket supplied does not fit your window, obtain appropriate material locally to provide a proper installation seal. 8 A CAUTION: To prevent broken glass or damage to windows, on vinyl or other similarly constructed windows, attach the support bracket to the window side jam. B C Wood Vinyl 13 INSTALL THE AIR CONDITIONER IN THE CASE Make sure the ground wire is off to the side and slide the air conditioner into the case. Do not push on the controls or the finned coils. Make sure the air conditioner is firmly seated. Reinstall the locking bracket and screw removed earlier. Reconnect the ground wire to the air conditioner using the screw removed earlier. IMPORTANT: The ground wire must be reinstalled to ensure a proper ground. Press the ground wire against the unit to prevent it from being pinched when installing the front grille Remove the front grille from its box and remove the shipping tape. Grasp the inlet grille at the bottom corners and pull it forward. Unhook it from its top h...
Este manual também é adequado para os modelos :Hobs - CLIMATISEUR AEH18* (2.32 mb)
Hobs - CLIMATISEUR AEE23 (2.32 mb)
Hobs - CLIMATISEUR AEH25* (2.32 mb)
Hobs - CLIMATISEUR AEM18* (2.32 mb)