Wall Mounting Remove the wall mounting bracket from the back of the heater and using it as a guide (see Fig. 2) mark off the hole positions on a suitable wall (a minimum height of 2 meters is required from the floor level to the bottom of the bracket). Solid brick or concrete block walls must be drilled and plugged. Fix the wall mounting bracket to the wall and assemble the heater to the extension tube using a bolt and wing nut fitted into hole 1 shown in Fig. 3a. Rotate the heater as shown in F

. 4. CFS60, CFS90 & CFS120 Remove large knock-out from back panel of heater and feed appropriate supply cable (see ‘a’ in Fig. 6) to terminal blocks ‘c’. Make electrical connections as shown in Fig. 9 and fix cable in back panel using suitable cable gland (not supplied). By removing one of the smaller knock-outs and using 5 core cable (see ‘b’ in Fig. 6) make the control connections to terminal block ‘d’ also shown in Fig. 6. Fix this cable in the back panel using suitable cable gland (not suppl

45o 500mm Max. Min. 1000mm Min. 2 3a 1 3b 4 6 5 CFS30 CFS60 CFS90 CFS120 CFS30 7 70mm 70mm 1 2 c d 'y' a b y 2 3 x 1 a b d c CFS60 CFS90 CFS120 D 230-240V ~1PN E L N E L1 F H1 H2 T C M E L H D1 D2 CFS30 306 262 495 526 CFS60 386 360 565 630 CFS90 386 360 565 630 CFS120 386 360 565 630 9 8 10 12 CFS60 CFS90 CFS120 145mm 120mm 85mm SPC 1 2 3 T I 0 D N L1 L2 L3 380 - 415V 3PN + E T C M A B 1L1 3L2 5L3 13NO A1 2T1 4T2 6T3 14NO A2 2T1 4T2 6T3 14NO A2 1L1 3L2 5L3 13NO A1 N L F H1 H2 E 11 CFS60 CFS90 C

4) make the control connections to terminal block ‘d’ also shown in Fig. 4. CFS60, CFS90 & CFS120 Remove large knock-out from back panel of heater and feed appropriate supply cable (see ‘a’ in Fig. 6) to terminal blocks ‘c’. Make electrical connections as shown in Fig. 9 and fix cable in back panel using suitable cable gland (not supplied). By removing one of the smaller knock-outs and using 5 core cable (see ‘b’ in Fig. 6) make the control connections to terminal block ‘d’ also shown in Fig. 6.

Press button ‘2’ to select Fan only/Low heat/High heat. By pressing this button once Fan only is selected, pressing twice provides Low heat and by pressing three times High heat is selected. On the display screen (see Fig. 4) two temperature readings appear at the top of the screen. The room ambient temperature appears on the right and the desired temperature appears on the left hand side. Use buttons ‘3’ and ‘4’ to set the desired room temperature when Low or High heat is selected. The temperat

When replacing the fuse, a 13 amp fuse approved by ASTA to BS 1362 must be used. If the plug is not suitable for the socket outlets in your home, the plug must be cut off and an appropriate one fitted. A plug cut off from a mains lead will give a shock hazard if inserted into a 13 amp socket elsewhere in the house. To avoid this, it should be disposed of immediately. NOTE: The fuse cover of a non-rewirable plug must be refitted when changing the fuse. Should the cover become lost, the plug must

Remove the control moulding and top panel. 3. Change over the links on the Star / Delta Terminal Block to resemble Fig. 5a. 4. Remove the blue neutral wire from ‘N’ and connect into ‘L3’ in the Mains In Terminal block. 5. Replace the control moulding and top panel. Attention: If using an extension cable, ensure that it complies with local electrical regulations and is suitable for the loads shown above. Operation The heat output from this heater is regulated using the rotating wheels shown in Fi

If 220-240V ~3P Delta supply is to be used a 4 Pin Plug is required (as denoted by * above). The Supply Cable is specifically chosen for each CFP heater and should only be replaced by a similar cable supplied by the manufacturer. See Fig. 4 for CFP Wiring Diagram. (References are listed below) A -Heat 1 Contactor B -Heat 2 Contactor C -Thermal Safety Cut-out Circuit D -Star / Delta Connector Blocks E -Heating Elements F -Mains Lead & Plug G -Earth H -Heat / Fan Selection Switch I -Thermostat T -

1000mm MIN. 380 - 415V 3PN + E H I C G 1L1 3L2 5L3 13NO A1 2T1 4T2 6T3 14NO A2 2T1 4T2 6T3 14NO A2 1L1 3L2 5L3 13NO A1 A B E D M TM F T Dimplex Industrial Fan Heater Models : CFP60, CFP90 & CFP120 THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE Electrical IMPORTANT SAFETY ADVICE DO NOT COVER OR OBSTRUCT the air inlet or outlet grille. IMPORTANT – Disconnect from the mains supply before carrying out maintenance work. THIS HEATER MUST BE EARTHED Keep combustible mater

Before switching on, please read the safety warnings and operating instructions. For your convenience, the heater is fitted with a rewireable plug incorporating a 13 amp fuse. In the event of replacing the fuse in the plug supplied, a 13 amp fuse approved by ASTA to BS1362 must be used. Electrical Dimplex Cheriton Fire Model : CHT20 08/18997/0 Issue 0 Important Safety Advice: When using electrical appliances, Basic precautions should always be followed to reduce the risk of fire, electrical shoc