Properly install front hand guard. This item can reduce injuries from kickback. Follow assembly instructions on page 6. Do not remove front hand guard. Do not replace front hand guard with substitute. The following steps will reduce the risk of kickback. • Use both hands to grip saw while saw is running. Use firm grip. Thumbs and fingers must wrap around saw handles. •Keep all safety items in place on saw. Make sure they work properly. • Do not overreach or cut above shoulder height. • Keep soli

Make certain you read and understand all Important Safety Information, pages 2 through 4.Improperuseof thischainsaw can cause severe injury or death from fire,electricalshock,orbodycontactwith moving chain, or falling wood. EXTENSION CORDS Use proper extension cords with this saw. Use only extension cords marked for outdoor use. The cord must be marked with suffix W or W-A following the cord type designation. Example: SJTW-A or SJTW. Use proper sized cord with this saw. Cord must be heavy enough

•Reduce the risk of the saw chain breaking or jumping off the bar. •Obtain optimal cutting performance. •Extend the life of cutting equipment. •Avoid increasing vibration levels. General rules •Only use cutting equipment recommended by us! See instructions under the heading Technical data. •Keep the chain’s cutting teeth properly sharpened! Follow our instructions and use the recommended file gauge. A damaged or badly sharpened chain increases the risk of accidents. •Maintain the correct depth g

REPAIR SERVICE Note: Only use original replacement parts. This will protect your warranty coverage for parts replaced under warranty. Each authorized service center is independently owned and operated. For additional service center or warranty information, call 1-800-858-8501. WARRANTY SERVICE If saw requires warranty service, return it to nearest authorized service center. You must show proof of purchase. If faulty materials or workmanship caused damage, we will replace saw without charge. NON-

Brainerd, MN 56401 1204 - 1st Road 317-282-5139 Hopkinsville, KY 42240 Franklin, MA 02038 218-829-5356 Wisner, NE 68791 502-886-7585 508-528-2013 402-529-6846 Lear Lawn & Garden Perry's Electrical Rebuilders 2204 N. Wolfe Street Maury's Fluorescent Appliance Beacon Lumber/Beacon Rental 24630 Hale Avenue NEVADA (NV) Muncie, IN 47303 1521 Bardstown Road 513 Church Street Forest Lake, MN 55025 Fallon Saw & Tool 317-282-6273 Louisville, KY 40205 New Bedford, MA 02745 612-464-8054 300 N. Marine St. 5

English English 8. Operation WARNING F7 F8 F9 F10 F11 It is very dangerous to run a chainsaw that mounts broken parts or lacks any parts. Before starting engine, make sure that all the parts including bar and chain are installed properly. ¦ STARTING THE ENGINE 1. Fill fuel and chain oil tanks respectively, and tighten the caps securely. (F7) 2. Set the switch to “I” position. (F8) (1) Chain oil (2) Fuel (3) Switch (4) Throttle lever (5) Throttle interlock 3. Pull out the choke knob to the second

Allow chain to cool down. Follow steps below to readjust saw chain tension. 1. Before adjusting chain, make sure guide bar nuts are only finger tight (see Figure 3). Also make sure adjusting block is in oval adjusting hole on guide bar (see Figures 3 and 4). 108539 16 SAW CHAIN TENSION ADJUSTMENT Continued 2. Turn adjusting screw clockwise until all slack is out of chain (see Figure 5). Note: There should be no gap between side links of chain and bottom of guide bar (see Figure 6). 3. Wearing pr

Even a non-moving chain can cause serious cuts to yourself or persons you bump into with an exposed chain. Long-term storage Empty the fuel/oil tanks in a well ventilated area. Store the fuel in approved cans in a safe place. Fit the bar guard. Clean the machine. See instructions under the heading Maintenance schedule. Starting and stopping WARNING! Note the following before starting: The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving ch

4820-13180 BOLT TORX M5xL20 T27 848-C3A-15B0 ARRESTER T2200-15110 MUFFLER T2200-15310 STAY T2100-15210 GASKET 848-C3A-15M1 BOLT 2850-15230 NUT 848-815-1400 SCREW M5xL14 T27 848-C30-14A1 INSULATOR T2200-31120 CAP 848-C30-14B1 GASKET, in 3330-14121 GASKET,carb 848-C3A-8100 CARBURETOR ASSY 848-C30-82A2 MANIFOLD 2867-82210 BOLT M4x70 848-825-1601 SCREW TP5(P-tight)xL16 T27 848-C30-82F2 ROD CHOKE T2200-83100 CLEANER 848-C30-31A2 COVER T2200-51110 DRUM 1/4x8T o60 848-C30-5121 CLUTCH 848-C30-51E2 • SPR

With flat file, round off front corner of cutter depth gauge (see Figure 23). After several hand filings, have authorized service center or sharpening service machine sharpen chain. This will insure even filing. Figure 22 - Depth Gauge Tool On Chain Flat File Depth Gauge Slot Figure 23 - Round Off Front Corner Of Depth Gauge Depth Gauge Tool Depth Gauge Front Corner .025" CLEANING AND MAINTENANCE Continued WARNING: Unplug chain saw from power source before servicing. Severe injury or death could