Orbital action provides a faster cut, but with a less smooth cut across the material. In orbital action, the blade moves forward during the cutting stroke in addition to the up and down motion. NOTE: Metal or hardwoods should never be cut in orbital action. To adjust the cutting action, move the cutting action lever (H) between the four cutting positions: 0, 1, 2, and 3. Position 0 is straight cutting. Positions 1, 2, and 3 are orbital cutting. The aggressiveness of the cut increase as the lever

YOUR FEEDBACK IS VITAL TOTHE SUCCESS OF DEWALT'S QUALITY IMPROVEMENT PROGRAM. See our catalog on the World Wide Web at INSTRUCTIVO DE OPERACION, CENTROS DE INSTRUCTION MANUAL SERVICIO Y POLIZA DE GARANTIA. ADVERTENCIA: GUIDE D'UTILISATION LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. SI TIENE DUDAS, POR FAVOR LLAME. MANUAL DE INSTRUCCIONES DW746, DW746X Woodworker’s Table Saw Scies circulaires a table d’entrepreneur Sierra de banco para madera Definitions: Safety Guidelines The definitions b

For all refurbished delta product, the warranty period is 180 days. delta may require that electric motors be returned prepaid to a motor manufacturer’s authorized station for inspection and repair or replacement. delta will not be responsible for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone other than an authorized delta service facility or representative. Under no circumstances will delta be liable for

Battery pack could be short circuited causing damage to the battery pack and possibly causing severe burns or fire. • Charge the battery packs only in DEWALT chargers. • NOTE: The batteries in your battery pack are the nickel–cadmium type. Cadmium is considered to be a toxic material by the Environmental Protection Agency. Before disposing of damaged or worn out Nickel–Cadmium battery packs, check with your state Environmental Protection Agency to find out about special restrictions on the dispo

Lower vise lever then tighten vise on work by using crank (see Figure 5). 30 15 FIG. 3 WRENCH FENCE FENCE BOLTS VISE 30 15 15 0 45 30 FIG. 4 383823-01/DW870 5/3/02 1:33 PM Page 7 383823-01/DW870 5/3/02 1:33 PM Page 8 English To Adjust Vise Stop CUTTING ANGLE Use the wrench to loosen the two hex bolts (Fig. 3). (Do not remove the bolts). The fence can be rotated in either direction. Securely tighten both the bolts before use. Switch To start the tool, FIG. 5 depress the trigger switch shown in Fi

1-800-4-DEWALT • INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA INSTRUCTION MANUAL DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVOANTES DE USAR EL PRODUCTO. GUIDE D'UTILISATIONMANUAL DE INSTRUCCIONES DW861W Heavy-Duty 4-1/2" (114 mm) Wet/Dry Masonry SawDW861W scie a maconnerie a sec/a l’eau de 114 mm (4-1/2 po) a service intensifSierra industrial de 114 mm (4-1/2 pulg.) de corte humedo o seco para mamposteria DW861W DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286 (MAR05)

392261-00 DW7464 Copyright © 2002 Before returning this product call 1-800-4-DEWALT IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR DEWALT PURCHASE, CALL 1-800-4 DEWALT. IN MOST CASES, A DEWALT REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TOTHE SUCCESS OF DEWALT'S QUALITY IMPROVEMENT PROGRAM. See our catalog on the World Wide Web. INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA INSTRUCTION MANUAL DE GARANT

390268-00 DW746 Copyright © 2000 Before returning this product call 1-800-4-DEWALT IF YOU SHOULD PURCHASE, CALL 1-800- IN MOST CASES, REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER IF YOU HAVE A SUGGESTION OR GIVE US A CALL. YOUR FEEDBACK IS VITAL TO THE SUCCESS OF DEWALT'S QUALITY IMPROVEMENT PROGRAM. See our catalog on the Wide Web. INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA INSTRUCTION MANUAL DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. SI TIENE DUDAS,

Asegurese que las lenguetas encajen bien en las aberturas. NO monte la sierra sobre la base en ninguna otra direccion. • Asegure la sierra a la base con pernos de 1/4” x 1-1/2” en las cuatro esquinas. ||SYMBOL| PRECAUCION: Asegurese que la sierra este firmemente montada sobre la base antes de usarla. PARA CERRAR LA BASE DE LA SIERRA DE BANCO • Quite los cuatro pernos, levante la sierra de banco de la base. • Levante la base por los rieles superiores y cierrela PRECAUCION: Asegurese que la sierra

Worn blades may also have insufficient body clearance which increases the chance of binding and increased loading. 6. LIFTING THE SAW WHEN MAKING BEVEL CUTS Bevel cuts require special operator attention to proper cutting techniques - especially guidance of the saw. Both blade angle to the shoe and greater blade surface in the material increase the chance for binding and misalignment (twist) to occur. 7. RESTARTING A CUT WITH THE BLADE TEETH JAMMED AGAINST THE MATERIAL The saw should be brought u