Assessments - 6, GPA: 4.2
(
)
)
|
Facilidade de uso
• Illustrations on this user’s guide may differ from your machine depending on its options or models. Check your machine type (see "Front view" on page 21). To see for paper weights for each sheet, refer to "Print media specifications" on page 109. Types Traya Plain . Thick . Thin . 2. Menu Overview and Basic Setup 44 Media and tray Types Traya Bond . Color . CardStock . Labels . Envelope . Preprinted . Cotton . Recycled . Archive . a. The paper types available manual feeding in tray. (.: Included, Blank: Not available) Envelope Printing successfully on envelopes depends upon the quality of the envelopes. To print an envelope, place it as shown in the following figure. • When selecting envelopes, consider the following factors: -Weight: should not exceed 90 g/m2 otherwise; jams may occur. -Construction: should lie flat with less than 6 mm curl and should not contain air. -Condition: should not be wrinkled, nicked, nor damaged. -Temperature: should resist the heat and pressure of the machine during operation. • Use only well-constructed envelopes with sharp and well-creased folds. • Do not use stamped envelopes. • Do not use envelopes with clasps, snaps, windows, coated lining, self- adhesive seals, or other synthetic materials. • Do not use damaged or poorly made envelopes. 2. Menu Overview and Basic Setup 45 Media and tray • Be sure the seam at both ends of the envelope extends all the way to the corner of the envelope. 1 Acceptable 2 Unacceptable • Envelopes with a peel-off adhesive strip or with more than one flap that folds over to seal must use adhesives compatible with the machine’s fusing temperature for 0.1 second about 170°C (338 °F). The extra flaps and strips might cause wrinkling, creasing, or jams, and may even damage the fuser. • For the best print quality, position margins no closer than 15 mm from the edges of the envelope. • Avoid printing over the area where the envelope’s seams meet. Labels To avoid damaging the machine, use only labels designed for use in laser printers. When selecting labels, consider the following factors: • -Adhesives: Should be stable at your machine’s fusing temperature about 170°C (338°F). -Arrangement: Only use labels with no exposed backing between them. Labels can peel off sheets that have spaces between the labels, causing serious jams. - Curl: Must lie flat with no more than 13 mm of curl in any direction. -Condition: Do not use labels with wrinkles, bubbles, or other indications of separation. • Make sure that there is no exposed adhesive material between labels. Exposed areas can cause labels to peel off during printing, which can cause paper jams. Exposed adhesive can also cause damage to machine components. 2. Menu Overview and Basic Setup 46 Media and tray • Do not run a sheet of labels through the machine more than once. The adhesive backing is designed for only a single pass through the machine. • Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged. Card stock/ Custom-sized paper • In the software application, set the margins to at least 6.4 mm (0.25 inches) away from the edges of the material. Preprinted paper When loading preprinted paper, the printed side should be facing up with an uncurled edge at the front. If you experience problems with paper feeding, turn the paper around. Note that print quality is not guaranteed. Must be printed with heat-resistant ink that will not melt, vaporize, or • release hazardous emissions when subjected to the machine’s fusing temperature for 0.1 second (about 170°C (338°F)). • Preprinted paper ink must be non-flammable and should not adversely affect machine rollers. • Before you load preprinted paper, verify that the ink on the paper is dry. During the fusing process, wet ink can come off preprinted paper, reducing print quality. 2. Menu Overview and Basic Setup 47 Media and tray Setting the paper size and type After loading paper in the paper tray, set the paper size and type using the control panel buttons. If your has machine for +/-buttons on the control panel (see "Control panel overview" on page 24): You can set the machine’s settings by using the Device Settings in Samsung Easy Printer Manager program or Machine section in Printer Settings Utility program. • For Windows and Macintosh users, see "Device Settings" on page 276. • For Linux users, see "Using Smart Panel" on page 279. It may be necessary to press OK to navigate to lower-level menus for some models. Select (Menu) button on the control panel. 1 Press System Setup > Paper Setup > Paper Size or Paper Type. 2 Select the tray and the option you want. 3 Press OK to save the selection. 4 Press (Stop/Clear) to return to ready mode. 5 • The settings set from the machine driver override the settings on the control panel. a To print from an application, open an application and start the print menu. b Open Printing Preferences (see "Opening printing preferences" on page 55). c Press the Paper tab and sel...
Este manual também é adequado para os modelos :Impressoras - SCX-3206W (7.97 mb)
Impressoras - SCX-3400 (7.97 mb)
Impressoras - SCX-3400/ALG (7.97 mb)
Impressoras - SCX-3400/STS (7.97 mb)