2. Place the resin disc in front of the appropriate size pad and push the adapter lock down through the center of the pad and discs. 3. Hand tighten the adapter lockdown, then insert the holding tool into the hole shown in Figure 2. Insert a large screwdriver into the slotted hole on the adapter lock down and securely tighten. DUaL aCTIOn SanDerS Begin sanding with an abrasive grit coarse enough to remove the high spots and any excessive roughness. Follow with a second sandpaper using a grit one

Stop using any tool if discomfort, numbness, tingling, or pain occur, and consult a physician. Operation LUbrICaTIOn Proper lubrication is the owner’s responsibility. Failure to lubricate the air tool properly will dramatically shorten the life of the tool and will void the warranty. REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping. © 2010 Campbell Hausfeld/Scott Fetzer For parts, product & service information IN241203AV 2/10

No oil in tool 2. Lubricate the tool according to the lubrication instructions in this manual 3. Low air pressure 3a. Adjust the regulator on the tool to the maximum setting (If applicable) 3b. Adjust the compressor regulator to tool maximum while the tool is running free 4. Air hose leaks 4. Tighten and seal hose fittings if leaks are found 5. Pressure drops 5a. Be sure the hose is the proper size. Long hoses or tools using large volumes of air may require a hose with an I.D. of 1/2” or larger

1. Lire attentivement tous les manuels, y compris celui de ce produit. Bien se familiariser avec les commandes et l’utilisation correcte de l’equipement. 2. Seules les personnes bien familiarisees avec ces regles d’utilisation en toute securite doivent etre autorisees a se servir de l’outil pneumatique. Ne MANUEL pas depasser la pression maximum de service de l’outil pneumatique (621 kPa-90PSI). Ceci peut diminuer la duree de l’outil. 3. Ne pas depasser la pression nominale de n’importe quel ele

This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear. This manual contains information that is very important to know and under-stand. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize this information, observe the following symbols. Danger indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Warning indicates a potentially hazardou

14. Do not put hands near or under moving parts. 15. Always secure workpiece in a vise or clamp. Do not misuse this product. Excessive exposure to vibration, work in awkward positions, and repetitive work motions can cause injury to hands and arms. Stop using any tool if discomfort, numbness, tingling, or pain occur, and consult a physician. Operation LUbrICaTIOn Proper lubrication is the owner’s responsibility. Failure to lubricate the air tool properly will dramatically shorten the life of the

4 voir la Garantie a la page 8 pour de l’information importante sur l’utilisation commercial de ce produit. Instructions d Utilisation TL0504, TL0518, TL1005, TL1118, PL1551, FHT504, IFT218, PL1504, TL1004 Veuillez lire et conserver ces instructions. Lire attentivement avant de commencer a assembler, installer, faire fonctionner ou entretenir l'appareil decrit. Protegez-vous et les autres en observant toutes les informations sur la securite. Negliger d'appliquer ces instructions peut resulter en

Protegez-vous et les autres en observant toutes les informations sur la securite. Negliger d'appliquer ces instructions peut resulter en des blessures corporelles et/ou en des dommages materiels ! Conserver ces instructions pour references ulterieures. Ponceuses Description Les ponceuses sont des outils pneumatiques concues pour les applications d’automobile sur les surfaces plates et courbees. Deballage Lors du deballage, l’examiner soigneusement pour rechercher toute trace de dommage susceptib

2. Turn the air tool upside down. 3. Simultaneously (at the same time), pull the trigger and pour a teaspoon of Campbell Hausfeld oil in the air inlet. After an air tool has been lubricated, oil will discharge through the exhaust port during the first few seconds of operation. Thus, the ex-haust port must be covered with a towel before applying air pressure. Failure to cover the exhaust port can result in serious injury. 4. Release the trigger and connect the air tool to the air supply. Cover th

tional starting. Ensure the switch is in el rango de la rectificadora, es decir, in a risk of fire and electric shock. If the off-position before connecting to el disco debe tener un rango limpiarse con un pano humedo. ELECTRICAL SAFETY NUNCA use solventes para limpiar an extension cord must be used, power source and/or battery pack, pick- superior a las 11.000 RPM. No use Mantenga la proteccion de seguridad piezas de plastico. Podrian make sure: ing up or carrying the tool. Carrying un disco co