For answers to your questions about this product, call 7am-7pm, Mon.-Sat., or 10am-7pm, Sun. • 1-800-235-5878 Time) (Hoo,s,is,edareoentro, Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. 530088731 10/11/01 Warranty Statement 2 Parts Available 10 Safety Rules 2 Storage 10 AssemblyOperation 5 8 Troubleshooting Table 10 Maintenance 9 Spanish 11 Service & Adjustments 10 Parts Ordering Back Cover FULL ONE YEAR WARRANTY ON SEARS CRAFTSMAN ELECTRIC BLOWER If this Craftsman Electric Blower fail

As the small off-road engine engine owner, you should be aware that Sears may deny you warranty coverage if your small off-road engine engine or a part of it has failed due to abuse, neglect, improper maintenance, unapproved modifications, or the use of parts not made or approved by the original equipment manufacturer. You are responsible for presenting your small off- road engine to a Sears authorized repair center as soon as a problem exists. -16 Warranty repairs should be completed in a reaso

Press the tubes together until the lower tube is fully seated in the upper tube. You will know the tubes are fully seated when the lower tube will no longer go into the upper tube. (About 3 inches). \ Attach Upper & Lower Tubes Figure 8 Figure 5 H,n = n,,,,, ====r= ASSEMBLY =n = =,,=, ATTAC'HING COLLECTION BAG (Fig. 9 ) • Slide the opening of the collection bag over the blower outlet. Pull the strap with Velcro tightly through the buckle and secure the Velcro tabs. NOTE: Make sure the strap with

5. Holding inlet cover open, slide upper tube into the air intake opening untiIthe latch on the locking ring snaps into place. Figure 4. 6. Install the screw in the screw tab on the vacuum tube. Figure 4. Tighten securely. 7. Fit the opening of the bag over the blower outlet. Make sure the vac bag strap is located completely ,.................. ................................ ????_,.. It ii i ,, , Blower Tube Blower Outlet Btower Tube Figure 1 ]ll]]lllllllllllllIIIllIIII I II II II Illllllll II

Bottom view Latch Area of unit Vacuum Inlet Cover (closed) Latch Area Vacuum / nlet Cover (opened) 3. Turn the inlet restrictor counterclockwise and remove it from the unit. Do not close the inlet door. You will next attach the vacuum tubes. \ Vacuum \ ,_ _ Inlet Cover Inletri__ tube release button is on top. Restrictor Attaching the vacuum tubes There are 2 vacuum tubes, an upper tube and a lower tube. The upper tube has a vacuum assist handle attached to one end and is cut straight on both end

Then, two tubes together until tube is securely seated in tube (about 3 inches). Upper Tube Lower Tube ATTACH THE COLLECTION BAG restrictor 3.Turntheinletcounterclock-Slide the opening of the collection bag removetheunit.Do wiseanditfromover the blower outlet. Pull the velcro notclosetheinletdoor.Youwillnext strap tightly through the buckle and se attachthetubes. vacuum cure to the velcro tabs. NOTE: Make sure the velcro strap is located on the blower outlet as shown below. Also, make sure the z

Inspect the insulation and connectors on the unit and extension cord before each use. If there is any damage, do not use until damage is repaired by your Sears Service Center. • Do not use the unit if the switch does not turn the unit on and off properly. Have the unit repaired by your Sears Service Center. • Avoid accidental starting. Be sure the switch is in the OFF position and keep your hand and fingers away from the switch while connecting the unit to the power source or when carrying a uni

358.794772 • Safety • Assembly • Operation • Maintenance • Parts List • Espa_ol, p, 20 WARNING: Read and follow all Safety Rules and Operating Instructions before first use of this product. For answers to your questions about this product: Call 7 am-7 pm, Mon.-Sat., or 10 am-7 pm, Sun. 1-800-235-5878 _.oors,,s,edaroT,,'_ ceo,,o, Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. 545167641 Rev. 4 4/16/08 BRW Warranty Statement 2 Storage 13 Identification of Safety Symbols 2 Troubleshooting

An undersized extension cord will cause a drop in line voltage resulting in loss of power and overheating. If in doubt, use the next heavier gauge. The lower the gauge number, the heavier the cord. • Do not use multiple cords..Keep the extension cord clear of operator and obstacles at all times. • Tie cord to cord retainer and connect to recessed plug as shown in this manual to prevent damage to unit and/or extension cord and to reduce the possibility of the extension cord disconnecting from the

• Stop the motor immediately if you are approached. DOUBLE INSULATION CONSTRUCTION This unit is double insulated to help protect against electric shock. Double insulationconsists constructionoftwo separateofelectrical "layers"insula tioninstead ofgrounding. Toolsandapplianceswith builta doubleinsulationare systemnotin tendedtobegrounded. Nogrounding meansisprovidednor onthisunit, shouldameansbeadd ofgrounding edtothisunit.Asaresult,theexten sioncordusedwithyourunitcanbe plugged120volt intoanypol