SPRAY MIST ® Button 2. Power “ON” Indicator Light 3. Power Cord 4. Heel Rest 5. Large Water Reservoir 6. Fabric/Temperature Dial 7. Soleplate 8. Easy-to-Fill Water Tank 9. Steam Dial 10. Steam Vents . 5 FILLING THE WATER RESERVOIR You must fill the water reservoir with water to use the SPRAY MIST ® feature and to get steam out of your iron. TIP: Sunbeam tests each iron at the factory to ensure that they function correctly. The test may leave a small, harmless amount of water within the water res

To clean the Soleplate: 1.Allow the iron to cool and then wipe it with a soft, damp cloth. WARNING: DO NOT use abrasive cleansers, scouring pads or vinegar to clean the soleplate. This will damage the finish. 2.Run the iron over an all-cotton cloth to remove any residue. USING THE SELF-CLEANING FEATURE You should use the Self-Cleaning feature once a month to maintain the optimal performance of your iron. To use the Self-Cleaning feature: 1. Move the Steam Lever back and forth from O/Off (Dry) se

• If an extension cord is absolutely necessary, a 15-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the extension cord so that it cannot be pulled or tripped over. FOR PRODUCTS PURCHASED IN THE UNITED STATES AND CANADA To reduce the risk of electrical shock, this appliance has a polarized plug (one blade is wider than the other). This plug fits a polarized outlet only one way; if the plug does not fit fully into the outlet, reverse the plu

7.Press the self-clean button and hold. Water will begin dripping from the steam vents. To make sure that all of the water is removed from the tank, slowly rock the iron side to side and front to back for 30 seconds. When rocking the iron, dip the nose of the iron slightly below the rear of the iron to make certain the water circulates completely. Release self-clean button after one minute. 8.Turn the iron upside down and allow the remaining water to flow out of the fill hole. 9.Dry the soleplat

How To Use the Special Functions SPRAY MIST ® The SPRAY MIST ® feature dampens the fabric to aid in removing wrinkles from heavy fabrics and for setting creases. To use the SPRAY MIST ® feature: Press the SPRAY MIST ® button firmly. AUTO-OFF When the iron is plugged in, the Power “ON” Indicator will light steadily, indicating that the iron is heating. If you leave the iron: • in a vertical position (on its heel rest) without moving it, the iron will automatically turn off after 15 minutes indica

. . . 7 Using the Iron’s Special Features . . . . . . . . . . . . . . 7 SPRAY MIST ® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Caring for Your Iron After Use . . . . . . . . . . . . . . . . 7 Turning Off Your Iron . . . . . . . . . . . . . . . . . . . . . . 7 Storing Your Iron . . . . . . . . . . . . . . . . . . . . . . . . . 8 Maintaining Your Iron . . . . . . . . . . . . . . . . . . . . . . 8 Cleaning the Soleplate . . . . . . . . . . . . . . . . . . . . . 8 Ironing Tips .

Do not touch hot surfaces. Use handles. . To protect against electrical shock, do not immerse cord, plug or heating unit in water or other liquid. . Close supervision is necessary when any appliance is used by or near children. . Unplug from outlet when not in use and before cleaning. Allow to cool before cleaning the appliance. . Do not operate any electrical appliance with a damaged cord or plug or after the appliance malfunctions or has been dropped or damaged in any manner. Return appliance

2. Plug the cord into a 120-Volt AC outlet. 3. Turn the large Fabric Select Dial to the fabric setting you desire (Silk or Synthetics). Allow the iron to heat for 2 minutes. While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface. NOTE: While the Steam Lever is turned to the O/Off (Dry) setting, you may still use the SHOT OF STEAM® or SPRAY MIST® feature. Please make sure the water reservoir is 1/4 full of water. TIP: Refer to the Ironing Guide for the

The Power Indicator will blink to let you know that the iron has stopped heating. IMPORTANT: The Power Indicator will continue to blink until the iron is unplugged or reset. TO RESET THE IRON: Move the iron back and forth and allow it to reheat for 2 minutes. The indicator will stop blinking and the iron will start heating again. WARNING: Motion Smart® Auto-Off is a safety feature, not a recommended means for turning your iron off. See “Caring for Your Iron After Use” for information on turning